(800) 853-2651
SHOP NOW

Recent content by red30

Yesterday's Tractor Forums
  1. R

    Cockshutt 50/buda 273 pistons

    I have them 716-308-5987
  2. R

    Allis 175 gas cam grind

    Most importantly what rpms do you run it at 262 cams are good to 2500 rpms stock you can call me at 716 308 5987 I'll be glad to help in any way
  3. R

    Ford 134 cid

    hi I looked that 134 ford up its only 3.437 bore not 3.562 and there too tall for any reasonable compression ratio but if you get in touch with me I can help you out Mike LePard
  4. R

    Cockshutt 50 Deluxe

    HI Yes take it apart you can bore it .060 over I have pistons if you need them most parts are still available from Phil heisey or myself 716-308-5987 Good luck Mike LePard
  5. R

    ONE STD PISTON FOR COCKSHUTT 50

    HI I think I'm the only guy for new 50 pistons. .030 or .060 over most used ones have broken ring lands or warn out ring groves 716-308-5987 Mike lePard
  6. R

    18-28 head gasket

    I may have one 716 308 5987
  7. R

    Buda rear seal

    Yes it has to stretch a lot any problems let me know I have put alot of these together this is mike lepard I think we've talked before
  8. R

    Buda rear seal

    Bottom pic is correct and dont forget to install the wear sleeve on the flywheel
  9. R

    Cockshutt 262

    I found the post you were looking at. with the changes it will work. head gasket that thickness about $150 offset piston pin bushings is a pain I have done it lol will cost you about $20 or more each plus the bushing. also need to machine pistons for snap rings
  10. R

    77 engine in 66

    hi if you get it in there and pull it much don't expect the rearend to last long its a pretty weak point of the 66
  11. R

    Cockshutt 262

    hi this is Mike LePard that 235 piston will give you 18.2 to 1 compression a little much lol I have looked hi and low for cheap options theres not much out there. 13 to 1 needs 114 octane gas to give you an idea you can call me anytime to discuss I will check some numbers that have been...
  12. R

    85 MF 242 LP vs. Gas differences

    do you have any of the heads that could be flow tested I have a flow bench and would be glad to help ya out I might be in Wauseon
  13. R

    85 MF 242 LP vs. Gas differences

    wow there are also different heads gas 1754691m91--- 242lp 1017248m91----223lp 1754898m91 the valves seam to be all the same number hope this helps
  14. R

    85 MF 242 LP vs. Gas differences

    hi looks like there were 3 options gas 830967m92---- high alt 835519m91-----lp 835518m92 I was involved with building a 33 massey engine same engine family you can call me 716-308-5987 we have a 85 around here for sale do you have your tractor yet lol Mike LePard
  15. R

    Zack Peterson, I need some help!

    I might be willing to trade 33 parts for 44 parts in equal shape lol. first does your top shaft have ball bearings or tapered timken type bearings there was a serial number break and they wont swap without some work..716 308 5987 you can call me too
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top