(800) 853-2651
SHOP NOW

Recent content by RedBarnNate

Yesterday's Tractor Forums
  1. R

    2640 Pressure Plate Adjustment Bolts Loose???

    I explained this to the owner, but he said he didn't want to mess with changing the clutch shaft. His call. He did tell me to switch from the metallic button disc to the woven style disc. He changed his mind half way through the repair. That's ok with me.
  2. R

    2640 Pressure Plate Adjustment Bolts Loose???

    The flywheel is well worn so the wear surface is about flush with the non-wear surface. The pressure plate, disc, and bearings only had 400 hours. I'm a bit uncomfortable grinding the ends of the shaft. The customer said he didn't want to go any deeper into the repair for fear of opening up...
  3. R

    2640 Pressure Plate Adjustment Bolts Loose???

    The flywheel is well worn so the wear surface is about flush with the non-wear surface. The pressure plate, disc, and bearings only had 400 hours. I'm a bit uncomfortable grinding the ends of the shaft. The customer said he didn't want to go any deeper into the repair for fear of opening up...
  4. R

    2640 Pressure Plate Adjustment Bolts Loose???

    Well maybe they aren't, but the real reason why the gears were grinding with clutch pedal fully depressed was because the bolts that keep the pressure plate together had all failed!
  5. R

    2640 Pressure Plate Adjustment Bolts Loose???

    http://forums.yesterdaystractors.com/viewtopic.php?t=1145496 In the above thread, they were called snubber brakes, so that's what I called them haha.
  6. R

    Deutz 6275LU Slow Hydraulic Cycle Time

    I thought I'd close this thread by sharing the solution to the problem. Russ was a good assistance in fixing this problem! We ended up checking the main hitch control unit - all valves OK. We isolated and checked the loader control valve mounted on the fender - loader valve OK. We...
  7. R

    2640 Pressure Plate Adjustment Bolts Loose???

    I agree. I think the input shaft causes the clutch disc to "hang up" on clutch release & could be the reason why the pressure plate rattled itself apart? I can't find my 2640 book to help me find out what's involved in changing the input shaft.
  8. R

    2640 Pressure Plate Adjustment Bolts Loose???

    I only mentioned the snubber brake because I found this older discussion topic listing it as a possible issue why the tractor would not go into gear when parked, but result in grinding gears. http://forums.yesterdaystractors.com/viewtopic.php?t=1145496
  9. R

    2640 Pressure Plate Adjustment Bolts Loose???

    Yes we installed a complete assembly. The first picture is the wear surface part of the pressure plate. The second picture is the release mechanism. The snubber brake keeps the gear train from spinning when disconnected from clutch. Yes we have the new clutch parts ready to go in. I'm...
  10. R

    2640 Pressure Plate Adjustment Bolts Loose???

    Hello! 3 years and 400 operating hours ago, the following parts were replaced on a JD 2640. All parts ordered through JD Dealer ([b:aeb33aa476]clutch release fingers should have been adjusted from factory[/b:aeb33aa476]). - new pressure plate - clutch disc - release...
  11. R

    Deutz 6275LU Slow Hydraulic Cycle Time

    Remote Coupler Control Levers ^ Hitch Valve ^ Tandem Hydraulic Pump ^ Front End Loader Control Valve ^ Front End Loader Control Valve Manifold ^
  12. R

    Deutz 6275LU Slow Hydraulic Cycle Time

    OK Updated Info: I Pressure/Flow Tested the Pump by plugging a flow/pressure meter in to the rear remote hydrualic couplers. At 2200 engine rpm, my pressure test with the adjustable pressure valve fully OPEN was showing 8.9 GPM. At 2200 engine rpm, my pressure/flow test with the adjustable...
  13. R

    Deutz 6275LU Slow Hydraulic Cycle Time

    Hi thanks for the reference. I called Russ and he gave me some ideas. Thank you! (Still looking to see if I can find rated hydraulic pump GPM at certain pressure and engine rpm).
  14. R

    Deutz 6275LU Slow Hydraulic Cycle Time

    Hello! Back story: Deutz 6275LU - hydraulic line replaced recently. Hydraulic oil and filter changed. Frond end loader reconnected and now having problem with slow cycle time of front end loader. Also slow cycle time when raising 3 point hitch. Front end loader is plumbed through rear...
  15. R

    Ford 950 (900) 12 Volt Conversion

See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top