Recent content by Reinders

  1. R

    Looking for a diagnosis

    Or one more thought, could it be the hydraulic unit? I replaced the old one with a used hydraulic. Maybe if I pull that first and try running the tractor to see if that is my problem. Any thoughts that could be my issue?
  2. R

    Looking for a diagnosis

    It does move just fine in neutral with engine off and the shifter seems fine. So now I don't think it is in the transmission. Would it make sense that a spring snapped on the clutch housing.
  3. R

    H Water Pump packing

    Thanks a bunch.
  4. R

    H Water Pump packing

    Thank you very much. I will try tightening first. The only trick now is trying to get a wrench on it. I should be able to, otherwise I'll pull the front end. Thanks again!
  5. R

    H Water Pump packing

    Just finished up on a Farmall H project and ready to get it out of the door, I do have a minor coolant leak that I didn't see before. I know it is the packing nut. My question is, "Aside from trying to just tighten the nut, is there packing material that precedes putting the nut in?" I took the...
  6. R

    Farmall H Magneto Timing

    Got it. I have it timed now and it seems to be working. I needed to take the magneto gear off and shift the teeth a little. I didn"t have to match up timing. Seems to be working just fine with the notches on the front pulley. Thanks for all the help.
  7. R

    Farmall H Magneto Timing

    Ok that works. Having never done this before, I watched a youtube video on how to time the magneto on a Farmall Cub. I would assume it would be the same on an H minus the firing order could be different. I attached the URL to that youtube clip in case anyone was interested. If anyone wants to...
  8. R

    Farmall H Magneto Timing

    That is what I thought too about the governor. I was pretty certain that it didn't have a mark. But when setting the magneto, it just didn't feel right and that is when I was thinking about the timing mark. I will take off the housing and look for a mark. It would make sense that they put a mark...
  9. R

    Farmall H Magneto Timing

    From what I am seeting with older posts is that there is a timing mark on the Magneto gear. I missed that (sorry, first farmall rebuild). My question is what are my options for getting that Mag gear timed? Do I have to remove the front cover? Hopefully not. Also, was there a timing mark on the...
  10. R

    Farmall H Magneto Timing

    I am to the point of timing the magneto and while I was in the middle of it I has one of those "Oh Crap" moments. I set the timing marks on the cam/crankshaft when putting the engine back together. My question is "Are there timing marks on the governor and magneto gears that I forgot to line up...
  11. R

    2 Farmall H questions

    You are absolutely correct and again I should have know better. I do have a pine board between the blocks and chassis and a jack stand in front of the blocks, but still all of you are right about the blocks. Dumb move on my part. The front end is back on now so I'm all set now.
  12. R

    2 Farmall H questions

    The tractor was taken completely apart and every part was sandblasted. The chassis was left intact from the clutch housing back. That part was needle scrapped. Then prime, paint, and now rebuilding.
  13. R

    2 Farmall H questions

    Thanks for the relies abut the blocks. Good to know and I should have known better. I am going to weld up a split stand and use that for next years project, JD model A. Sorry, no red next time around.
  14. R

    2 Farmall H questions

    Thank you very much.
  15. R

    2 Farmall H questions

    Here is a before picture back in September if you were interested.
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top