-
R
Owners manual needed
This is an Allison Chalmers R3000 7 ft offset disk. Does anyone have any info on this disk. Thanks- rgvnaa
- Thread
- Replies: 5
- Forum: Implement Alley
-
R
Ford NAA steering problem
Does it require a complete disassembly. What should be the next move to get this going. -
R
Ford NAA steering problem
I was moving my Ford NAA when I felt a pop. The steering now only turn to the Right, and the entire shaft now backs out about 3 inches when I turn to the left and the box does not move the tires to left. I know something is broken and I hope someone can point me in the right direction so I can... -
R
FINISHED - 641 Restoration with lots of pics
So the big question, what was the cost of the restoration. Did you do all the work your self? Subing out work adds a bunch to restoration. Tractor looks sweet by the way. If I had that it would never be used. -
R
ford 631 piston leak
That plug was tight. I did use the bolt and washers method. I tapped it in flush after I cleaned it. -
R
ford 631 piston leak
Well it was not tight at all. It was kinda lose. I had put a "close" size oring but it felt to tight. Should it be tight with the oring or lose. The original oring just barely is bigger than the oring groove. The picture is a replacement oring that was as "close" as I could get it to the... -
R
ford 631 piston leak
Another thing, could the fluid be to thin I'm using UTF 134 from TSC. Maby thicker oil will kill the smaller leaks. -
R
ford 631 piston leak
Thanks for the replies. This picture was taken with the lift going up. Well i was thinking that the bobbing on the three point might be because of theses leaks. I'm only really concerned about the bobbing. If these leaks are considered somewhat normal, then were should I look for the bobbing... -
R
ford 631 piston leak
Hello. I'm gone through the hydraulic system 3 times already I have changed all the orings and the system appears to have pressure now there is no problem with the lift it picks up fast and strong. Although I'm still having a problem with the leaking down and a slight bobbing I took off... -
R
Worth a look.
That's a deal. If it was in my neighborhood I'd be all over the that. Probly $2000+/- in repairs. Its a $4000 tractor here in south Texas. -
R
Ford 640 Overload Valve help Needed ASAP
Thanks for responding. The squirt of oil is more continuous and with pressure and only through the lift not when it goes down. Should the oring be tight or should it be more of a metal seal. I'm thinking I put a large oring and the valve is stuck some way. What do you think. -
R
Ford 640 Overload Valve help Needed ASAP
I to used a punch and drove the valve and plug out together. Can this piece leak at pressure when fixed and installed. When the left goes up a jet of hydraulic fluid shoots out. Is there a separate oring kit that I can get other than the orings that come with the lift kit. Sorry to get in the... -
R
Stream of hydraulic fluid
Hello, I replaced all the orings and gaskets of the lift cover on my ford 631. I followed a video and IT book I bought. Well the bobing is gone and the lift is nice and strong, but now when I take the hydraulic fill cap off I can see a stream of hydraulic fluid shoot ing from the area of the...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy