(800) 853-2651
SHOP NOW

Recent content by rjfinke

Yesterday's Tractor Forums
  1. R

    Case ih 1460 setting help

    We are now close to 10 to 15 degrees after talking with several other people and hearing about this angle setup. We actually welded a plate on the throat plate that catches the header so that we had more adjustment then the couple of bolts holes. We did find that the manual talks about throat...
  2. R

    Case ih 1460 setting help

    It is after 81 and the header height control is working correctly letting it float and carry fine and when we manually set it down completely we still have that much cylinder available. Trouble is we just cannot seem to get the front/knife down so we aren't leaving 4"-6" of stubble and losing...
  3. R

    Case ih 1460 setting help

    Looking for help setting and adjusting case ih 1460. It was leaving 4 to 6 inches last year, so we tried raising the backend where it bolts to the axle but tried beans yesterday and it seems to be the same. So now looking for ideas. The rear tires are 18.4-16L that are 45" with 10psi and the...
  4. R

    John deere number 15 subsoiler clutch disassembly.

  5. R

    John deere number 15 subsoiler clutch disassembly.

    Thanks for the help, it just seems to be stubborn and do not want to ruin the shaft or anything. Hoping to find out why it doesn't turn to go forward, ratchets in reverse, and doesn't trip down. Do I have my puller correct? Don't want to push on the shaft (it goes partially out the back then)...
  6. R

    John deere number 15 subsoiler clutch disassembly.

    I bought a john deere number 15 trip sub soiler at an auction over the weekend and I know it is after 1942 since it has an enclosed clutch assembly. It has been modified and beefed up, but the trip clutch doesn't work (it clicks in reverse, but does not rotate in forward). The clutch looks...
  7. R

    John deere mt

    Just recently purchased a john deere mt to add to our antique tractor collection and was wondering if there was anything I should specifically look for or be concerned about. Also, I have read several posts that say you should have the m and the mt manuals, is this true? The previous owner...
  8. R

    Ford 4500 pto addition?

    Is it possible to add a pto onto a ford 4500 tractor? The tractor is industrial with a loader on it, but it does not have nor did have the backhoe that you see on some. The reason I ask is that it has a blank plate where a pto would normally be and my friend that owns it would like to put a...
  9. R

    Farmall F 12 over drive

    Do you know how many we're made or used on the f series tractors?
  10. R

    Farmall H Extra gear/lever

    Yes it does look similar to the picture.
  11. R

    Farmall H Extra gear/lever

    I am looking for information on Farmall H's. The h has an extra push rod or control on the right hand side of the control/steering pedestal, I think tht it is maybe a creeper gear, but I have read about heisler transmissions with a control rod and wonder how I tell the difference. Also, I...
  12. R

    Farmall F 12 over drive

    I am looking for information on Farmall over drives. Specifically I am looking for information on f 12 overdriveI. Information that would be helpfully would be pictures and brochures about them, number made, details, etc. Any help would be appreciated.
  13. R

    Case 1070 AgriKing help/pictures

    We are working on a 1070 that had rear end trouble and we split it and put on a new rear end, we took pictures and have the manual but we still have a few things that are not quite falling into place. Some pictures of other tractors would be helpful. Ours has the power shift so similar would be...
  14. R

    cracked engine block

    I have put Bars Leak in it and it still seems to happen. Are there any other product recommendations on what to use or how to go about it? Also besides having to change the oil more often does anyone see any issues with putting a valve in to drain the water or have an idea where the best place...
  15. R

    cracked engine block

    I have restored a TO-20 and it had an issue of water in the oil when I started, but I thought if I put new gaskets and what not on it it would eliminate or slow down the problem. Unfortunately I found a small hairline crack in the bottom of the block, with everything back together now I still...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top