(800) 853-2651
SHOP NOW

Recent content by rkelm

Yesterday's Tractor Forums
  1. R

    Wood Chipper

    Thanks for all the information, it is helpful. I do have a Kubota L3800 I inherited with only 300 hrs. I have rented a commercial chipper several times and they do great, I have cedar trees mostly that grow into the trail around the place, (this place is 130 acres with about 60 percent woods...
  2. R

    Wood Chipper

    I am thinking of obtaining a PTO driven wood chipper for a tractor, will a 2N/9N (I have a mixed machine) be able to run this machine and does this type of equipment put an undo load on any tractor.
  3. R

    fuel flow issues

    Take a look at the cap.
  4. R

    is my tractor a 9n or 8n??

    This is of little help but there are a lot of these machines out there that the previous owners put together parts as they could find them. They didn't have the internet to keep them "official", they were using them to be functional and it didn't matter what it looked like - if the parts fit and...
  5. R

    Loss of power

    Hello, I need a little help. My 2N (given to me by my mother-in-law a couple of years ago) with some 9n and 8n parts is loosing power when a load is put on the tractor. It runs like a top in neutral but when you engage the PTO with shredder it bogs down so to speak and then when you put it in...
  6. R

    Turning

    Thanks for all the comments. I do have some weights I can add to the front. The brakes are a little bit of a problem, the previous owner before my father-in-law obtained it was a little disabled and had a special platform added on the left side so you can't access the left brakes. Only the...
  7. R

    Turning

    Would weights on the front end of my 2N help with the turning. Kind of tired of using the whole county to turn around without "plowing" with the front wheels. Any suggestions are welcome and needed. Thanks.
  8. R

    Off topic

    Douglas, you were tested by the Almighty. You will be blessed farther than you can imagine. Thanks for the uplifting today. There is hope for us all. God Bless you and all those that help others.
  9. R

    ford 9n leak question

    My father-in-law bought what he thought was a 9N and called it that for years. Some things just didn't add up so I did some research. Here is what I found about the 2N's: 1947- Numbers 9N258540 to 9N306221 1946 - 9N198767 to 9N258539 1945 - 9N170018 to 9N198766 1944 - 9N126575 to 9N170017...
  10. R

    Freak happening

    And lawyers seem to think there is no "accidents" anymore - always want to prove someone is responsible. Let them stand behind or in front of one of these accidents and they would think other.
  11. R

    OT: Zero Turn advise

    I have an old cub cadet 126 gear drive (when they made them like a little tractor) and you can't beat it and makes zeros look like junk. Wish they still made them like that, I had the largest mowing company in town when no one wanted to do it and I had another 126 that was the work horse that...
  12. R

    Part numbers/ How to test coil

    I was having some problems with the 2N under a load and noticed a leaking governor and thought it was that but suggestion with this site said to change out the points, condenser, etc. and I was just checking about the coil in case it might be that as well (just trying to cover all the bases). I...
  13. R

    Part numbers/ How to test coil

    Does anyone know the part numbers for points, condenser and rotor for a 12 volt front mounted dist. from NAPA for a 2 N Ford Tractor? Looks like I may need them. Also, how do I test the coil to see if it is ok. Thanks
  14. R

    Governor

    It is 12volt. Do have a steady flow with unscrewing the bolt from the bottom of the carb. Have a filter inside the tank for the bowl and then the bowl filter. Found a piece of wood inside tank and cleaned out tank and filters as mentioned. The flow out of the bottom of the carb was after I...
  15. R

    Governor

    My 2 N is acting up. It runs well for about 30 minutes and then starts coughing (like the governor is trying to adjust to the load). It spits and sputters and then sometimes dies. I have to limp back to the barn. While it spits and sputters it lurches and this is hard on me just having two...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top