-
R
Air Compressor Recommendations
Guys, I really appreciate all your comments and advice! A lot of good information here from obviously knowledgeable folks! A lot of thinking and planning to be done on my part. The structure of my 40X30 shop has just been completed and electrical service is still to be done. I m really glad to... -
R
Air Compressor Recommendations
Looking for recommendations for a quality brand of air compressor for my new shop about 3 to 5 hp. Will be used to run air tools, sand blasting, and painting. Thanks! -
R
Oil Pressure Gauge Repair
I plead temporary insanity. After seeing what s involved, it s obviously not practical. My NAA project is more a rejuvenation than a complete restoration. However, I am, sometimes, a glutton for punishment. Thanks for your advice and the video link!- RMGeorge
- Post #1
- Forum: Restoration Processes
-
R
Oil Pressure Gauge Repair
My Rochester oil pressure gauge from my Ford NAA is stuck on 40 psi. It s old, rusty, and hasn t been used in years. I would like to restore it instead of replacing it. Anyone have any experience opening up the gauge for inspection and repair?- RMGeorge
- Thread
- Replies: 4
- Forum: Restoration Processes
-
R
NAA Part ID Question
I m referring to the two smaller Allen head plugs above the two that hold the oil pump. -
R
NAA Part ID Question
Can someone identify the two small Allen plugs on the block outside the distributor housing along the distributor and oil pump shaft? What is their purpose? -
R
No Spark NAA
Tractor is running now. First start in 12 years. Cleaning the new points with a dollar bill did the trick. Thanks to all for the help! -
R
No Spark NAA
Have all new wiring and ignition components on the NAA I’m restoring. New 12 volt internally resisted coil. Twelve volts all the way to the points. No spark at plugs, none. Replaced condenser…no change. Replaced rotor and distributor…no change. Plugs and points are set to correct gap. Why no... -
R
NAA Front Axle Bent ?
This morning I ran a string from one end of the axle to the other. With the axle positioned squarely at the forward end of its travel along the pivot pin, the string was perfectly parallel with the front face of the crankshaft pulley. I m convinced now that I do not have a problem with the... -
R
NAA Front Axle Bent ?
Wheels are not currently on the tractor. I have it disassembled for a partial restoration. Just installed new bushing and pivot pin and remounted the axle center section today. Tractor has not been used in 12 years, so I don t remember if wheels towed out or not. -
R
NAA Front Axle Bent ?
Can anyone tell me what the correct degree of bend is for the center section of the front axle of my NAA? Both ends of my axle center section are about 7 inches behind center (about equally bent). Both radius rods are bent. Thanks!
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy