(800) 853-2651
SHOP NOW

Recent content by Rob Tholin

Yesterday's Tractor Forums
  1. W

    Lilliston Rotary cutter gearbox parts

    I have 3 Lilliston rotary cutters and need gearbox parts for them. If anyone has any information on where to find parts for the Warner Auburn WA50-1 gearboxes, please post a reply and let everyone know so we can all get back to mowing.
  2. tomstractorsandtoys

    Case 730 gas

    There is a Case 730 CK narrow front close to me for sale. It says engine is loose but needs new electrical parts. Looks like all the plug wires are missing. They want $1500. Good deal or not? I do not need it at all as I have way to many tractors already but have always liked the looks of the...
  3. D

    1206;1256;1456 stories

    Like below,lets hear about 1206;1256;1456.I have one each of 1256 and 1456.Bought the 12 in 2000(moveing up from a turbo 706),bought the 14 5 years ago in 'pieces'(mechanic special).Always thought the '12' was pretty 'salty'. But the '14' will just do circles around it.It will litterally play...
  4. H

    John Deere 830

    I recently got a Schwartz 1800 qt loader. I’m trying to hook it up to a John Deere 830. It has a Gresen 2712 V hydraulic pump. I haven’t been able to find any schematic or diagrams on how to hook one up thanks.
  5. H

    3550 transmission leak

    Hi everyone. I am new to this forum and new to tractor repair. I just bought a ford 1974 3550 with the bucket attachment. It had a spun rod bearing and a leak at the bell housing. I have separated the tractor and the clutch is soaked in hydraulic fluid. From what information that I can find...
  6. A

    Mccormick deering 1929 10-20

    I am working with my son on getting the 1929 Mccormick Deering 10-20 going, we need a new fan belt I believe the old one was 1.25 width and 50 ttl length. Any help would be much appreciated, someone at the local parts said it should be leather, the one that was in place was cotton and rubber
  7. Y

    1020 steering shaft arm

    I just got a 1020 that is in overall great shape. The problem is a small leak that is behind the steering shaft arm. This is the arm that can be seen behind the round inspection plate on the left side of the tractor. If I decide to replace the seal behind the arm, how do I get the arm off? It...
  8. A

    Oliver Summer Show

    Who is headed to the Summer Show this weekend in Emporia, KS?
  9. 3

    JD CAM BEARINGS

    Tractor is a 1957 J D 420C 113.3 Crawler. HELP, I have a question about cam bearing installation. The rear bearing is 1 1/4" long & has an oil hole 3/16" from one end & 3/32" from that hole is a semi-circular cutout which is at the edge of the bearing. The block has an oil slot which is...
  10. E

    2600 Injection pump leak?

    I noticed a small leak that is coming from the end of the diesel injection pump. Is this a DIY project or does it have to go to a pump rebuilder?
  11. R

    Tecumseh motor blowing oil

    I just bought a chipper/shredder with a 8Hp. Tecumseh engine. It runs good and seems to start OK with barely getting the flywheel moving. the problem I am having is after an hour of run time I noticed oil coming out from the base of the fill tube. I am not sure how much oil came out yet as I ran...
  12. O

    H carburator idle screw

    H idle screw sized now broke off have drilled a small hole in it and heated it no go. Can anyone tell me the tape size to retap treads? Thanks
  13. I

    4020 Electrical ?

    Has anyone had issues getting a good ground on a 4020? This is a 1967 gas. It is a 12 volt system with two 12 volt batteries. Each battery has a hot cable direct to the starter and each battery is grounded to the frame. My batteries were junk - so I just put 2 new ones in. Still nothing. I...
  14. V

    Engine troubles...

    Hi there, I've just started opening up my Ferguson engine on a bench, and 2 of the big end bearings were flopping around. Would that have caused the knocking in the engine? The shell bearings were more than half worn down those two con rods, and had melded on to them. Does that indicate that the...
  15. M

    Case 530. No start...

    Hi! New tractor owner here with a starting problem. Background: We bought a Case 530(at least that was how it was advertised, the serial number plate is missing) a couple of weeks ago. Gas engine. Watched it start, drive forward and reverse, hydraulics on FEL(model 31) and Eagle hitch work...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top