(800) 853-2651
SHOP NOW

Recent content by rockjeep

Yesterday's Tractor Forums
  1. R

    Square bale stacker

    Back in the 50s when my dad was young he traveled around South Dakota with a man that made an implement that went on a square baler to stack the bales in a pyramid. Similar to this Zimmie stacker but way before it s time. I was wondering if anyone had any information on something like that or...
  2. R

    HELP Hard to find wrist pin bushings for a Huber

    I found out that Crower cams will custom make the bushings at a very reasonable price. They have saved my day.
  3. R

    HELP Hard to find wrist pin bushings for a Huber

    They are not really worn. The bushings just have a little more slack than I would like to put them together
  4. R

    HELP Hard to find wrist pin bushings for a Huber

    From what I can tell nothing else used this motor. They used them for power plants and well pumps.
  5. R

    HELP Hard to find wrist pin bushings for a Huber

    Nope they are not going to work. Back to looking I guess. I m bout ready to scrap the original engine and just do a small block Chevy
  6. R

    HELP Hard to find wrist pin bushings for a Huber

    Ok I had a place order me some of these that are within .001 of what I measured for the outside diameter. The inside will need to be honed out a scosh and have the oil hole added. Hopefully this material will work for what I need...
  7. R

    HELP Hard to find wrist pin bushings for a Huber

    We do have a IBT here in town I will check with them but then It will be the problem of finding a machine shop that will do it.
  8. R

    HELP Hard to find wrist pin bushings for a Huber

    Bob The two machine shops that I talked to "looked" in their books and couldn t find anything. I looked online yesterday with no luck but I will talk to my parts guy today they have tons of old books in the back.
  9. R

    HELP Hard to find wrist pin bushings for a Huber

    I have talked to a couple machine shops but none want to do it.
  10. R

    HELP Hard to find wrist pin bushings for a Huber

    This is a 1937 Huber model B with a Buda hp205 I have found most of the parts to hopefully finish putting my motor together but having a hard time finding the wrist pin bushings. I have been searching till my eyes are crossing. The measurements I have are Bushing OD 1.376 Pin OD 1.130...
  11. R

    Buda gas engine swap. HELP

    Where are you located? the only other engine I have found is in CO and I am in Arkansas. Got any pictures of yours?
  12. R

    First time painting a tractor

    No not my first time painting just my first tractor paint job and it was hard on a fatguy. Thanks.
  13. R

    First time painting a tractor

    Thanks. It?s a urethane
  14. R

    First time painting a tractor

  15. R

    First time painting a tractor

    Well I guess you can?t upload photos from a phone
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top