(800) 853-2651
SHOP NOW

Recent content by rocko

Yesterday's Tractor Forums
  1. R

    Hydra Power Drive Shake in high range

    Thanks, I'll take a look. Best to see from bottom i'd figure?
  2. R

    Row crop 88 sheet metal

    Hi Gary, I got a couple 88's sitting out in the yard, one is a RC. Got most all what your looking for plus last I messed with it a running motor. Other is a Supper 88 wider rear end just a hood but it's been butchered in past to take a larger battery, missing all other sheet metal. Also has a...
  3. R

    Hydra Power Drive Shake in high range

    Exactly 5th gear was where it was worst. Did feel it in lower gears high range though. Never tried 6th high. What exactly is or where is this HPD jack bolt? Thanks for the help.
  4. R

    Hydra Power Drive Shake in high range

    Thanks rrlund, I took a look at the chain coupler and I am not missing any rollers but most all rollers on trany side are loose and easily rolled by finger and are very tight and unmovable on the H P DR side. Thinking may just order a new chain or in the mean time split and flip it so opposite...
  5. R

    Hydra Power Drive Shake in high range

    Hello folks, I have a 1550 diesel with the Hydra Power Drive. The H P Drive has just recently started to shake fairly severely when I put it into high range. Just wondering what is going on and what this shake is an indication of or what to come. Feels like it may be ready to let go. I have...
  6. R

    Rossa Master leak on Oliver 1550

    Yes it was surging and RPM's changing without throttle movement, that why I started chasing an air leak. I took the timing plate off and it is turning there when cranked, Tried starting no start bit more fuel pouring out, no pressure to speak of at injector line I had nearly completely loosened...
  7. R

    Rossa Master leak on Oliver 1550

    Been chasing an air leak in the fuel lines and filters for a couple days, seem every time I thought I had it, it still would not start come morning. Could still get her running by bleeding injectors for bit and then she'd run for the short time I needed her or maybe catch air while running...
  8. R

    Thanks to rrlund

    Thanks for your opinion and advice. Towed the 1550 outa the field, removed loader (ease on} so not so bad, dropped 3pt bale roller and towed and pushed into shop. All with no other driver. Tore into her and finally remove clutch. You were right, Splines on clutch plate were total worn away...
  9. R

    1550 Hydra Power Drive

    On thinking on it longer, it makes more sence to me what you were suggesting. I figure if the center did break out of clutch would have no preasure as hydra drive isn't turning. It does try to turn when clutch is released but not fully it seems. That for sure will mean pulling motor but I've...
  10. R

    1550 Hydra Power Drive

    Well it seems to disengage properly when pushed in and no longer grinding noise happening with clutch in. Noise starts when clutch released. I did go out and try it again in both direct and hydra power and loosened the filter again near off with higher revs. No flow hardly at all, bubles a...
  11. R

    1550 Hydra Power Drive

    I'll keep the offer in mind. May come down to that but will not be sure for a bit. Where abouts are you located.
  12. R

    1550 Hydra Power Drive

    Hydra Power Drive seems to have just gone out instantly. Clutch seems to be operating properly. Hydra P Dr turning when clutch out and making grinding sounds. Removed chain coupler to trany and both joining gears seem to be still engaging the shafts at least by hand. Loosened filter on Hydra...
  13. R

    Central MN snow storm how ya'll sitting?

    i'm a little further north than you. southern Alberta Canada. started snowing last night and been coming all day, about 6 inches so far. supose to carry on all night again. actually our second snow fall, had about 4 inches last sunday but that all melted off last week. think this one might be...
  14. R

    68 ford c series cab over hydraulic clutch problems

    thanks willie. yes i know exactly what your speaking of. just to clarify what your saying, the resivoir is actually under that boot? I was looking for something a little bigger like on a more modern vechicle. as a side question would it be the same set up for the brake fluid as when i was out...
  15. R

    68 ford c series cab over hydraulic clutch problems

    thanks jim, i'm going to go out to the shop and have another look. i'll let you know if i find it. thanks for the responce. rocko.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top