(800) 853-2651
SHOP NOW

Recent content by roger gregory

Yesterday's Tractor Forums
  1. R

    Ford 801 hydraulic problems

    hank all of you for the help. I replaced the damaged spool valve in the unloading assembly and the system is working well.
  2. R

    Ford 801 hydraulic issues

    hank all of you for the help. I replaced the damaged spool valve in the unloading assembly and the system is working well.
  3. R

    Ford 801 hydraulic issues

    pulled the cover and freed up the unloading valve (it has some damage), now when I start the engine the lift raises but will not lower until I kill the engine. Do I need to replace the unloading valve assembly?
  4. R

    Ford 801 hydraulic problems

    I freed up the hyd. unloading valve and re-assembled, We are half-way there, now when I start the engine the lift raises to the top but will not lower without killing engine. The unloading valve had some damage, I may have to replace it. What are you thinking?
  5. R

    Ford 801 hydraulic problems

    ark, I removed the top cover today and the item 11 hydraulic unloading valve was stuck as you thought. I hope to re-assembly tomorrow. One question the barrel the "o" ring slides in (I do not know the tech. name) has one small notch on one end and two large notches on the other end, do the...
  6. R

    Ford 801 hydraulic issues

    hank you very much, I will pull the cover off on Monday and pull and free up the part. I will let you know how it works out.
  7. R

    Ford 801 hydraulic issues

    am sorry that I did not give enough detail. The part I freed up when I installed the LCRK was part 21 NCA913T the Hyd. valve lift control. The part I did not check was part 11 C9NN925A the Hyd. lift unload valve. If someone could please help, what do I need to do next.
  8. R

    Ford 801 hydraulic issues

    Hello, I just purchased a Ford 801 that had sit 1.5 years. I have everything working except the 3-point lift. I pulled the top cover and installed a LVRK (repair kit with "o" rings) and freed up the small spring loaded control valve, I did not remove the larger valve next to the control valve. I...
  9. R

    Ford 801 hydraulic problems

    ould the unloading valve be stuck and not allow the arms to lift?
  10. R

    Ford 801 hydraulic problems

    Please respond to my question about the hydraulics on my Ford 801 Power Master.
  11. R

    Ford 801 hydraulic problems

    have removed the side cover and started the tractor. In the raise position there is no fluid visible, in the lower position there was a small amount of fluid running out of the back of the control valve cover. The fluid stream was small about the size of a #2 pencil. What should I do next?
  12. R

    Ford 801 hydraulic problems

    I am back working on my Ford 801 Power Master again. I pulled the side cover where the pto lever is per your request. In the up position there is no fluid moving in the reservoir, in the down position there is a small stream of fluid (about the size of a #2 pencil) coming from the back of the...
  13. R

    Ford 801 hydraulic problems

    es Sir, the un;loading valve was stuck and I freed it up when I installed the new LCRK. I did not remove the part next to the unloading valve, could this be a problem. Thank you for the help, I hope to work on the tractor again saturday.
  14. R

    Ford 801 hydraulic problems

    hank you so much for the information, I will check this on saturday.
  15. R

    Ford 801 hydraulic problems

    I just purchased a Ford 801 tractor that had been setting for a couple of years. I got it running great but the 3-point lift does not work. I clean out the hyd. reservoir and replaced the fluid. I vented all the air out of the system, the pump seems to work great, with top 3"x5" plate removed it...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top