(800) 853-2651
SHOP NOW

Recent content by Roger That

Yesterday's Tractor Forums
  1. R

    Ford 312635 Heavy Duty Spindle

    Most tractors that had the hd spindles had loaders on them so they took some abuse. Usable spindles are $75 plus shipping. Thanks
  2. R

    Ford 312635 Heavy Duty Spindle

    HD spindles are easily identified by the slight bulge in the lower part of the casting. Bulge is approx 3" from bottom of casting. Standard spindle castings are the same dimension from upper to lower area.
  3. R

    Ford 312635 Heavy Duty Spindle

    I've got a left side.
  4. R

    Ford 312635 Heavy Duty Spindle

    Confirming it is the left side side you need? Sitting on the tractor.
  5. R

    312635 spindle?

    Which side are you looking for? Pretty sure I have a left one.
  6. R

    19-105 (703) loader help

    Is this for the tilt cylinder? Can you post a picture of the entire piece you need? I've several of the cylinders lying around and may have the piece you need.
  7. R

    Wanted to buy, used

    I have a used cam that out of an early 1960's diesel motor. It fall in the "good to be ground" category. It is factory marked as diesel. $75 delivered
  8. R

    Ford 4610 with 4 cylinder

    Found this on clist. Owner states factory 4 cylinder instead of 3. Need one of the 3 cylinders guru's to say if it's original. https://chico.craigslist.org/grd/d/4610-ford-tractor-under-500/6647072279.html[/img]
  9. R

    Hydraulic Cylinder parts

    I have the parts you need. PM me Thanks
  10. R

    Who has a Ford 800 hydraulic piston pump

    If you decide to go with the piston pump and manifold, I have the parts. Email is open.
  11. R

    Need Help Decoding Ford/NH ID Tag

    You are correct. I missed putting in a digit on the model#. It should read CA6P4C
  12. R

    Need Help Decoding Ford/NH ID Tag

    You are correct. I missed putting in a digit on the model#. It should read CA6P4C
  13. R

    Need Help Decoding Ford/NH ID Tag

    I looked at a Ford New Holland that has been converted to a floor scrubber by Clarke and am considering converting it back to ag use. The tag under the hood reads: Tractor Number: *BD87857* Model: CA64C Unit: 5B01B Engine: BB526902 5A23 TRansmission: 5A26B Rear Axle: 5A06B Hrdraulic Pump: 5A04B...
  14. R

    Jub hyd pump trick to remove valve seats?

    The tool to remove the valve seats is called a blind hole puller.
  15. R

    Jubilee accesory plate

    I have the NAA 476-B that you need. Send me an email. Thanks, Roger
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top