(800) 853-2651
SHOP NOW

Recent content by rrobert

Yesterday's Tractor Forums
  1. R

    streering shaft for craftsman garden tractor

    Excellent link. The price isn't too bad considering Sears doesn't bother to keep it in stock.
  2. R

    streering shaft for craftsman garden tractor

    What state are you in? What is wrong with your steering shaft? What is the model name on you rider? I tried searching ebay and amazon using the part #. Try using the model name instead. I am in Michigan and know of 2 places to find parts for old machines. One is a seller on ebay. The other...
  3. R

    Parts for a Cub Cadet

    What state are you in? Ebay is a good place to check.
  4. R

    Gilson Montgomery Ward Wood Chipper

    How does that work? Looks too simple, small and unsafe!! Looks unusual. Do you have any top view pics? You might be able to sell it for $300+(very rough guestimate) to a collector. The value is whatever the buyer is willing to pay.
  5. R

    Hydrostatic Drive

    Look under the seat. There is a small shaft on top of hydro. If it is leaking there, then it is only a matter of time before it stops working. I would give it a few weeks to burp it and get air out. Next, I would try to use thicker oil instead of what is recommended. I have no experience...
  6. R

    214 jd riding mower

    I am not sure if the 200 series used the Onan engine. I would be skittish if it did tho. The Kawasaki engines seem very dependable.
  7. R

    214 jd riding mower

    I too would buy it in a heartbeat for $450 but woud be a little skittish if it has the Onan engine. I have a 185Hydro from the late 80s that I paid $300 for and had to repair to make run.
  8. R

    Wards Tractor

    You're welcome. Glad I was able to assist you! :) I was going to look in my Gilson parts manual that I have. But, I sold the same tractor you have 3 weeks ago and gave the manual to the buyer.
  9. R

    CASE 446

    jackssmallengines said NLA. "USE 3725884M1" But, I can't find that part anywhere.
  10. R

    CASE 446

    Email the $7 seller and ask if they have more than one to sell. I am sure you could go to a bearing shop with dimensions and find a replacement bushing if you needed to. Or, search granger for bushing diminsions. Last stop is to find any correct diameter idler pulley that will fit on the bolt...
  11. R

    CASE 446

    Ebay has two sellers with them. One is $7 and the other is $32. Ebay search C12264
  12. R

    Help with kohler governor linkage

    I used middle hole based on a 13 hp engine I saw in boneyard. Engine sounds ok. I can hear the governor working when pressing hydro pedal to go forward and reverse. I think the engine governor noise is more subtle because it is a 14 hp. I didn't want to set the idle screw to adjust the...
  13. R

    Help with kohler governor linkage

    That makes sense. But I am not sure how to set sensitivity. I am setting RPM by moving throttle cable. This rider is a hydro. When I go from reverse to forwoard, the front wheels pop off the ground. I don't have the weight of the deck on it, so that might solve that issue. I am going to...
  14. R

    Help with kohler governor linkage

    I don't normally remove spring from governor arm but this time I did...I didn't mark it a week ago and can't see any wear on the holes. Kohler CV14S. 14107 2832309131 The gov arm has three holes. Top is close to govenor shaft, bottom is furthest away. If I put the spring in top hole, the RPM...
  15. R

    Kohler Command 25

    Just realized. The one in the ebay pic has a flywheel cover. You would need to remove that so you can add your drive pump pulley to engine. If the seller is reputable, they should know for certain if they are interchangeable.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top