(800) 853-2651
SHOP NOW

Recent content by RussSt50

Yesterday's Tractor Forums
  1. R

    danuser md-6 post driver bearing

    thanks for the com follower bearing info. I am looking to try and fink one now. Thanks again
  2. R

    danuser md-6 post driver bearing

    I just bought a danuser MD-6 post driver. I need to replace a bearing, from the danuser site it is a 2156 bearing assembly. They are asking 49.40 plus shipping for it. Does anyone know of a replacement that doesn't cost that much or what measurements I can use to search for one ? Thanks
  3. R

    New Idea 484 belt replacement

    Thanks Bruce, that was helpful.
  4. R

    New Idea 484 belt replacement

    I need to replace one front upper belt on my new idea 484 round baler. It has mostly original belts that are endless, 2 ply. I would like to replace this one broken front upper belt, 11x73.25, with a splice, 3 ply belt. Has anyone done this, will I get into trouble doing this?
  5. R

    new idea 484 belt replacement

    i need to replace one front upper belt on my new idea 484 round baler. It has mostly original belts that are endless, 2 ply. I would like to replace this one broken front upper belt, 11x73.25, with a splice, 3 ply belt. Has anyone done this, will I get into trouble doing this?
  6. R

    Ford 3000 front axle bolts frozen

    Thank you for the explanation....makes sense.
  7. R

    Ford 3000 front axle bolts frozen

    Thanks. I was going to try to heat up the axle (so it would expand) - not the bolt ends. But I'll try heating the bolts first.
  8. R

    Ford 3000 front axle bolts frozen

    I am replacing the front L/H axle knee on my 1972 Ford tractor, but have run into a stone wall. I managed to remove the steering radius rod from the left front axle, but the bolts holding the left axle to the center axle will not budge. I've managed to get the nuts loose but the bolts won't...
  9. R

    Ford 2600 industrial backhoe

    Thanks - those are the ones I've been looking at but I just wasn't sure that the brake shoes for an industrial Ford 2600 backhoe would be the same shoes as those for a Ford 3000 & 2600 tractor.
  10. R

    Ford 2600 industrial backhoe

    The brakes on this backhoe are almost non-existent. The diesel engine on the backhoe is similar to my Ford 3000 tractor - are other parts similar? Does it use the same brake shoes as a Ford 3000 tractor? If not what brake shoes should I get?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top