(800) 853-2651
SHOP NOW

Recent content by Rust Farm John

Yesterday's Tractor Forums
  1. R

    hanging farmall wheel weights

    Ive run six sets per side on four sticks of 3/4" all thread. I cross drilled each stick with several holes so I could run hitch pin clips through each hole to keep the weights tight when I didn't have on a full stack. Four hitch pin clips per side. I ran the half weights. 75lbs is much easier on...
  2. R

    ensign filter

    Gotta have a gasket between the bowl and the base. Thanks for the Baldwin part number.
  3. R

    G708 is finally home

    Nice G708/707 LP. I have a G707LP and one G707 parts tractor. Im in OK as well. My tractors came from the Kiowa and Jackson county areas. I saw the chassis of a G704/MF98 in a salvage in Texas a couple of years ago. Maybe its still there.
  4. R

    The Final Harvest.

    Roger, Thanks for helping this young man make a memory and sharing it with us.
  5. R

    G707 Hydraulic problem

    When using the hydraulic remote on my G707 to lift or lower an implement, if the cylinder is holding the weight of the implement somewhere between full stroke any movement of the remote handle will first cause the implement to quickly drop a few inches as if there is not a load control check...
  6. R

    Thompson Rock-It Governor

    Sounds like a great buy on a Rock It governor. Why do so many on this board say bad things about Denny's? Is it pricing or is it quality or something else? I would like to know. I've bought a few pieces from them and I've been happy with what I've bought. I'm aways trying to watch out for...
  7. R

    Okla Pull at Pryor

    The Pryor pull was great! We had a good time. Thanks to everyone that made us feel welcome.
  8. R

    GCTC pull

    We are planning on being there.
  9. R

    Okla Pull at Pryor

    Yeah we have gotten about 0.80" at my place near Haskell since yesterday but it looks like less rain up towards Pryor/Adair. Time will tell.
  10. R

    Okla Pull at Pryor

    We plan on being there.
  11. R

    Farmall M lack of RPM governor?

    Thank you for the heads up.
  12. R

    Farmall M lack of RPM governor?

    Thanks! North Puller your the first to offer good advice to me on this site in a real long time. Thanks for the detail!
  13. R

    Tunica Pull

    Mean Green Pulling Team lists December 5-6-7, 2013 as the dates for the 2013 Tunica Southern Nationals. Hope this helps!
  14. R

    Farmall M lack of RPM governor?

    Last night I was trying to adjust the hi idle rpm on my M to be 20% over stock. I have been running a 3-4 yr old "magic" or hardware store spring and governor response has been good. I back out the hi idle limit screw and my rpm"s max out at about 1820 rpm with the screw not touching the stop...
  15. R

    2705 axle diameter

    Could any one tell me the rear axle diameter for a MF 2705 tractor? Thanks in advance!
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top