(800) 853-2651
SHOP NOW

Recent content by rustybronco

Yesterday's Tractor Forums
  1. R

    Farmall Model A finding TDC and starter issue

    heet metal pointer attached to sheet metal inspection cover is correct for 1939 and early? 1940 Farmall A's. In order to find TDC you can also pull the valve cover and make sure both valves on #1 are closed. Then it's a simple matter to use the crank to raise the #1 piston fully. Personally...
  2. R

    Farmall M upper hose is offset

    What do the hood gaps look like? Have you compared measurements from the new to the old rad? You could try making a wedge shaped pad for under the radiator. That should cause the rad to lean rearwards.
  3. R

    The Farmall M is 80 years old.

    y A will be 80 in July.
  4. R

    Oval hole in bell housing

    1942 appears to have have used a cover but not all years did.
  5. R

    Oval hole in bell housing

    Don't think the oval hole used a cover.
  6. R

    K&W spray Copper-Coat. Asking the experts.

    I just did the head gasket on my A. Hit it with permatex copper gasket sealant and didn't even think twice about it.
  7. R

    Re: Early H4 magneto kill swith

    n the case of my '39 A, it is original to what came on the tractor when new. The why's and why-fors you what have to ask the engineers that designed it. It might have to do with another type of machinery that operated the same way back then. Unfortunately the ignition system is live any time you...
  8. R

    Early H4 magneto kill swith

    orrected Autocorrect.
  9. R

    Early H4 magneto kill swith

    The bracket arraignment used to route the stop cable is probable in correct. The current parts catalogue shows two brackets used. The stop knob is incorrect. The originals used a know approximately the same size but it had the letter S in the middle. Mine is modified from the electrical kill...
  10. R

    Early H4 magneto kill swith

    'll take a few pictures in a short while.
  11. R

    Farmall Cub - Running but popping through air cleaner

    I looked at a cub low-boy a few months ago. Had a bent valve. It doesn't take too much to pull the side cover and look. Do a compression test and go from there.
  12. R

    Farmall B head Bolt Torque Sequence

    Correction... $17.03 plus shipping.
  13. R

    Farmall B head Bolt Torque Sequence

    No diagram but start with the middle stud on the side closest to the spark plugs then to either one of the center studs on the opposite side. Next is the other center most stud on the same side. After those three would be the stud diagonally outwards across from the last stud and so on and so...
  14. R

    no fire

    Also point gap issue, distributor cam runout.
  15. R

    Granddaughter old A

    t also has the correct right rear hub, steering wheel and the early front hubs. OP, I can remember putting my son on my '39 A when he was around her age.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top