(800) 853-2651
SHOP NOW

Recent content by rustymn

Yesterday's Tractor Forums
  1. R

    f2 gleaner

    i have a oat pickup head for a f2 i would be willing to sell. i live in southern mn.
  2. R

    f2 gleaner

    I need to change the engine drive belt on my f2 gleaner. what is the easiest way to get the traction control belt off and how does the hydraulic hose disconnect from the sheave.
  3. R

    engine sleeves

    Is there any difference between a wc and a 175 4 1/8 bore sleeve. I know the pistons are different, just wondering about sleeves.
  4. R

    AC combine

    I paid 1500 for my 90 that has the factory extension. turned around and sold my 66 for the same price.
  5. R

    wc governor

    I have a wc engine and I am wondering how much more hp or rpm do you get by switching to a d17 governor spring vs putting in a 175 spring. Also I have two different governors laying around and was wondering why they have different styles. They both look like the wc/wd's. they both have the same...
  6. R

    wc torque tube

    JMS/.MN, just wondering if you got my email.
  7. R

    wc torque tube

    Does any one have a torque tube for a allis chalmers wc? I dont need the shaft, just the housing. need one that has the lever for the rearend engagment.
  8. R

    WD45 loader hookup

    I put a shutoff valve on the rear port and on each of the lift arm cylinders. I can lock up the snowblower and use the loader or i can lock up the loader when using the snowblower. i use the highpressure shutoff valves. only drawback is I have to get off the tractor to switch the valves on the...
  9. R

    For You Allis Experts

    did any wd45"s come with the pin style drawbar instead of the snap coupler bell.
  10. R

    id engine on gleaner e3

    I have been told there are 3 different motors, 17-xxxxx-m is the d17 motor with 7.2 compression 17-xxxxx-z has 8.0 compression (found in e, e3 gleaners) 17-xxxxx-v has 8.2 compression found in the 170 tractors. as for different oil pressures, they changed the gear on the oil pump to get...
  11. R

    all crop 90

    wondering what my all crop 90 is worth, it is a humpback and has a factory extended bean head. has a scourkleen, and is in decent shape.
  12. R

    wheel tread

    is a 61" wheel tread width from inside to inside of tires?
  13. R

    Middle of wd45 engine rebuild...need help!

    If you just installed the crank and torqued the main caps. you should be able to turn over the crank by hand with a little effort if the rods are still not installed yet.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top