(800) 853-2651
SHOP NOW

Recent content by sandman2234

Yesterday's Tractor Forums
  1. S

    Farmall Cub - down on Compression

    I just wanted to mention that the hand reamer shown isn't leaving a very smooth surface where it cut. I realize that it was stated that they would lap the valves, but why? If you used a drill press, or a milling machine to power that same reamer, you could control the down pressure better which...
  2. S

    Big Tex 14GN 25+5

    I have a 2013 20+5 14GN with no issues other than the deck having to be replaced, going on the 3rd time. It is getting aluminum decking this time around. David from jax
  3. S

    Not mine ,wife said no

    Could be a little further and be here... David from jax
  4. S

    whats top dollar on a B Allis

    Might be my computer screen, but blow the picture up, and it appears that the torque tube has bleeding marks from the battery and who knows what else. A properly painted tractor shouldn't show that, just thinking to myself. About $1800 to $2000 is where I am at... but an in person view might...
  5. S

    Allis B Rear Light

    Dick L is correct in saying that the white light you have pictured is incorrect. The bullet shaped red ones are also incorrect for a B. The correct one has an almost flat clear lens, with the outer circumference having a red light. The red one is the hard part to find. I have several of the...
  6. S

    allis b with no front holes to locate side weights

    Not unusual at all. I have a couple that don't have holes in the plate that the side engine weights are mounted to. I thought about drilling one of those plates, but since I have the front axle weights, decided to just put those to good use. The front axle weights are probably better for your...
  7. S

    Brenda

    This message is a reply to an archived post by kendak on April 23, 2011 at 19:25:39. The original subject was "Brenda". She has made ever deal right, great bunch to work with!
  8. S

    CA cuts out when hot

    My mowing B does that, but it is because it has an unvented gas cap. I just loosen the cap and it starts running fine again. Guess I should find the correct gas cap, but it hasn't been a priority. David from jax
  9. S

    AC B side mower???

    I have one sitting out back by the blueberry bushes. Picked up another and loaded it on the upper part of my 5th wheel trailer. It is still sitting up there, haven't had any reason to take it off. That has been a couple months ago... David from jax
  10. S

    D-14 question

    I would run a compression test on the engine. Then squirt about four teaspoons of oil in each cylinder and run the test again. If the pressure increases drastically with the oil, then it is probably a ring problem. If you have one (the front one) that is low and oil in the cylinder doesn't help...
  11. S

    Repairing Tractor Gas Tank

    Red Kote would be my choice... David from jax
  12. S

    Allis One Way and Two Way plows for a B/C

    Thank you Zach! Was the R-hand plow a steel or cast moldboard type? David from jax
  13. S

    Allis One Way and Two Way plows for a B/C

    I am going to start looking for a single or set of the plows that mount on the back of the Allis B/C tractors. As far as I know, they are called one way and two way plows...assuming the one way to be a single (right plow) and two way to be a pair, (left and right plow). I know they came in steel...
  14. S

    ER kit for 1959 D17?

    Two days probably isn't enough, and I would use the 50/50 acetone/ diesel fluid as a penetrant. Good luck to you, some never give up, but most likely it will at some point. As far as the dished pistons, do you think it might have been for using Kerosene (ie distilate fuel?) Allis...
  15. S

    OC3 modification questions

    I have always been interested in a crawler. A small one, with D8 pulling capacity would be great but have to be realistic, lol. I own nothing Oliver, know even less, except a Cousin has completely restored an OC3, and WOW is it nice! There is a 3 way trade possible, a trailer for a...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top