(800) 853-2651
SHOP NOW

Recent content by Sclem

  1. S

    Fan housing 8N

    How to get fan housing to fit on a non OEM radiator on 8n Ford. Don't seem to fit. Thank you for any hints.
  2. S

    Starter removal, on 51 8n

    IT manual says remove cap screws & remove starter. The oil filter seems to be in way. Starter drive appears to be larger than original. What is the trick to get starter off tractor? Thank you for any information.
  3. S

    Vent on top of dome on 8n gas tank

    Does leakage occur out of vent on dome on tank when tank is about full & slopping around. If so is this normal? Thank you for any information.
  4. S

    Chunk cut out of wiring harness by theives on 8n ford.

    Battery stolen and wiring harness cut by oil filter & behind tool box and wires taken with battery. I thought I could just splice wire in but I have 4 wires from generator and 6 wires in harness by tool box. They cut bat cables. How do I hook 4 wires to 6 wires? Thank you for any information.
  5. S

    Removing seized frozen brake drum off 8n ford

    How do you remove a rusted & seized brake drum off a 8n tractor. Been setting & rusted for years. Thank you for any help.
  6. S

    8n ford hydraulic system

    HI: Lift lever in normal position will not move lift arms. I took back bolt out & tilted lever forward to rotate control shaft more counterclock wise to get lift arms to move. Where do I start to correct problem? Thank you for any information.
  7. S

    8n ford hydraulic lift arms

    What is wrong when control lever has to be turned farther than lever in normal position allows. I took back bolt out of control lever so as to rotate shaft farther counterwise to get lift arms to move upward. Now it will not lift arms. Where should I start for repairing the lift arms? Thank you...
  8. S

    Removing broken load nozzle in Farmall H carburetor

    Hi: How do you remove the broken thread end of the brass load nozzle from a H carburetor? Thank you for any information.
  9. S

    Square holed plug below torque on Farmall 300

    What size is square holed plug on bottom of torque on a 300 & where do I get a wrench that fits it? Thank you.
  10. S

    KEYSTONE 1 row corn planter in Wendel IH book

    The Keystone planter on page 35. Thank you.
  11. S

    KEYSTONE 1 row corn planter in Wendel IH book

    HI: Do any of you collectors know what kind of lid or cover went on the Keystone.1 row corn drill in the 150 yr IH book. I assume it was cast iron & would like to know if it had the name on it & if it just set on the hopper or if it was fasented to hopper. Thank you for any information
  12. S

    IHC 2 row pull type go devil cultivator

    Did IHC make a 2 row cultivator pulled by a tractor?
  13. S

    Where to buy main bearings for Mc Cormick tractors

    Where is the best place to buy the bearings for the 10-20"s? Thank you for any info.
  14. S

    row crop 300 transmission rear end oil capacity

    Hi: What is the oil capacity of the rear end on the Farmall 300? Thank you.
  15. S

    farmall 300 slips out of 5th gear

    .Farmall 300 only goes in 5th gear about half way & flies out of 5th gear when used. Goes in the other gears all the way & works good. Is the fork bent & needs replacing or what? Thank you for any information>
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top