(800) 853-2651
SHOP NOW

Recent content by scott morrow

Yesterday's Tractor Forums
  1. S

    ser #8 getting show ready

    Yes i will be bringing #8 and a ferguson 40 that is in original paint i would rate a 9 out of 10
  2. S

    ser #8 getting show ready

    just pulled ser #8 out of the corner where she has been sleeping for 2 years different carb new battery different generator clean gas tank and starter repaired and we are running. I won't leave it sit that long again lots went to h-ll from sitting but a good cleaning should still look pretty...
  3. S

    traveling to ferguson show

    anyone going to the show in wisconsin that will be close to marion kentucky i need something picked up thanks scott email [email protected]
  4. S

    dang cold

    just got home from work 630 am and its -15 below zero winds are 20 to 25 mph about -20 to 25 wind chill whats up wisconsin
  5. S

    ferguson 18 AO-28 plow

    jason parts books are not always right I have 3 single bottoms putting the 16in ones next to the 18in there is a hell of a difference between them. I recently restored my 18 found the same point as the red one in the pic got real lucky oliver made the moldboards for these plows and i found a...
  6. S

    ferguson 18 AO-28 plow

    The red point in the pic will fit your plow it just has a square tail not tapered like the one on your plow. The point on your plow is bent just heat it up and bend it back, as to the moldboard the 18in is a lot larger than the 16 in
  7. S

    axle weights

    thats the ones I am talking about inside the fender mounting with the fender bolts to the trumpet. i have 3 sets all are 150 plus a couple lbs each work great got rid of the fluid on my to30 and put a set of these on couldn't tell the difference
  8. S

    axle weights

    the weights you are talking about are 150 lbs each
  9. S

    Hey Sam...help me identify this plow share

    I am pretty sure it is a 18in I will look at my parts book do you want to sell it
  10. S

    fel for 50 massey

    I just put power steering on my ferguson 40 for 325.00 off of a 65 massey ferguson lots of them around just sold a completed set up needed some work for 250.00. My dad has a complete set up from a massey ferguson 50 in really nice shape I think he would let it go for 400.00. By complete I...
  11. S

    9 Disk--?BO-20

    I have one of these from what I have been told it was designed for the wheat stubble,only has to be pulled 2 to 3 inches in the ground at a very high speed. The stubble is left standing in clumps to hold the snow. The one in the pic is missing the tail wheel just like the disc plow it is very...
  12. S

    Joe Burke's auction

    Does anyone know why Joe is having a auction I haven't talked to him in awhile hope all is well with him
  13. S

    help need part

    I need a stone box for a ferguson disc figures I sold the 2 extra I had now I need one anyone that has one to sell let me know thanks scott at [email protected] or call 920-713-2774
  14. S

    Ferguson EO-20 sickle mower spring

    Mark I have what you are looking for give me a call at 920-713-2774 scott
  15. S

    TO35 Governor guts

    I just got done with a 55 to 35 put in 3 different governors with no results didn't work at all. tractor ran great idled great top rps good just no governor. My dad said to switch carb swapped it with a good used one I had dammed if the governor worked it was in the carb all a long go figure
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top