(800) 853-2651
SHOP NOW

Recent content by scottrolfing-HT

Yesterday's Tractor Forums
  1. S

    155d stalls after half hour or so...gets a little warm.

    norm, I'll pick one of those up tomorrow and try.
  2. S

    155d stalls after half hour or so...gets a little warm.

    Screwed a brand new one on.....No dice.
  3. S

    155d stalls after half hour or so...gets a little warm.

    I got the filter from hoye. Website says it has the correct anti drain back stuff
  4. S

    155d stalls after half hour or so...gets a little warm.

    Saga not over. After the tractor sits, merely for a few minutes, it takes as much as 30 seconds to regain oil pressure. The filter is empty on every start. I pulled the relief valve during the rebuild and replaced the ball. Is there any other way the oil could drain back besides through the...
  5. S

    Yanmar 155d clutch won't release

    Norm, that is a definite possibility.that would explain also why I tend to have a hard time getting it into gear...and the pto spins when I have the clutch depressed. Winston, no dowels in the flywheel except the one that holds it to the crankshaft.
  6. S

    Yanmar 155d clutch won't release

    Put it all back together....same thing...this I held the tractor from moving and I was able to do so.I drove it around the yard a bunch.seems to be working alright. I seem to be experiencing some chatter/howling coming from transmission/rear end at certain speeds......
  7. S

    Yanmar 155d clutch won't release

    No dowels. I called hoye before testing the PP and he said if the pins in the fork are good, only thing left is the pp. But now I know that it's working.
  8. S

    Yanmar 155d clutch won't release

    split it again this morning. went quite well actually. took the clutch and fly wheel off. i then bolted the PP on with the disc against the fly wheel and layed it flat on my drill press. used a piece of wood and the throw out bearing and carrier. i depressed the clutch fingers and the pressure...
  9. S

    Yanmar 155d clutch won't release

    There isn't a spec of rust on flywheel disc or PP. I'll have to split it again to get numbers....Bugger. we'll see what hoye says Monday.
  10. S

    Yanmar 155d clutch won't release

    I put it in the way that the friction disc has full spline engagement with the drive shaft.if it were flipped only 2/3 or less of the splines would be engaged. So long side to back of tractor.
  11. S

    Yanmar 155d clutch won't release

    Ok, some background. I rebuilt the engine for this tractor.while having it split I inspected the clutch parts. Friction disc was out of spec.flywheel was beat up and needed to be turned. I bought new friction disc and pressure plate from hoye. Had a machine shop turn the flywheel. Put...
  12. S

    155d stalls after half hour or so...gets a little warm.

    All back together and running! Had about 50 psi upon start up. Then gradually came down to around 22 psi at idle after warming up a bit. It runs good. Yay. Having a clutch issue though. I'll start another thread for that. Thanks everyone.
  13. S

    155d stalls after half hour or so...gets a little warm.

    Turns out the plug I'm talking about up by the pump on the side of the engine block is to help prime the pump.I pulled out that plug, hooked up my starter with the tractor in two halfs and jumped the starter...after about 3 ten second turns I obtained 7 psi on the gauge the third try. WOO HOOO...
  14. S

    155d stalls after half hour or so...gets a little warm.

    The plug I was thinking about is right up by the pump.
  15. S

    155d stalls after half hour or so...gets a little warm.

    Oh yes there is one there too. I'm line with pick up tube
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top