(800) 853-2651
SHOP NOW

Recent content by simon83

Yesterday's Tractor Forums
  1. S

    Ford 9N 12 Volt Conversion

  2. S

    Ford 9N 12 Volt Conversion

  3. S

    Ford 9N 12 Volt Conversion

  4. S

    Ford 9N 12 Volt Conversion

    spoke to my mechanic... when we bought the conversion kit 6V to 12 V there was a resister included which he installed as well.. the resister is frm ignition 12 v to 4.5. v the Coil only get 4.5 Volts... should we take out the resister
  5. S

    Ford 9N 12 Volt Conversion

    thanks for the Tips, having my retired mechanic friend (always busy) coming next week
  6. S

    Ford 9N 12 Volt Conversion

    converted with Kit to 12 V... Tractor started no problem, test drive all fine, back in the Garage, a week later, tractor does not start... spark plugs have no spark, also had a new coil... could it be the coil? before I take everything down again
  7. S

    Oliver Hart Parr Standard

    thank you will let them know
  8. S

    Oliver Hart Parr Standard

    Thank you... we will use it Thank you, we dont know what SAE Grade the Bolts are, we have a Manual but it does not say the Torque
  9. S

    Oliver Hart Parr Standard

    Hello we are restoring an Oliver 80 Standard in Austria. We would like to know the Torque on the Flywheel
  10. S

    Oliver Hart Parr Standard

    We are not quiet clear... The Piston has a diameter of 4,2460 " as we will make the sleeves should they have a Diameter inside of 4.2519 " ? or is the 0,004" radial? it seems very tight? Thanks
  11. S

    Oliver Hart Parr Standard

    thank you, we have the pistons... I will give the message to the mechanic Thank you
  12. S

    Oliver Hart Parr Standard

    Oliver standard 80 1941
  13. S

    Oliver Hart Parr Standard

    I asm only the interpreter between frm the mechanic.... he is making new sleeves, need to know the diameter of the sleeves or the distance between the sleeves and the piston... hope I am explaining it propely
  14. S

    Oliver Hart Parr Standard

    thank you for the tips.. we will try it
  15. S

    Oliver Hart Parr Standard

    we dont understand the meaning... we are in Austria, rebuilding an engine english is not our 1st language
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top