Recent content by SimonRidout

  1. S

    Milestone

    The Naval fellowship goes beyond national boundaries, I served 21 years in the Royal Navy. Met quite a few USN personnel, the fact that your ships are dry and ours are not probably helped! Like most things in life, there were good times and bad times, often very close together. My abiding...
  2. S

    No Tractor,,but,,,

    I was once using a wheel barrow to take material 300 metres down my drive way to fill pot holes, an old farmer told me that I should be using an internal combustion engine to move it, I replied that I was, 'a two cylinder armstrong'. We both had a good laugh.
  3. S

    Not to hijack the tool box thread but:

    Wait until you need sets of imperial and metric spanners and sockets. My tractors, Ferguson FE35, MF35X, Ford 4000 are imperial but my modern stuff, cars, lawnmowers, chainsaws are metric! Thats life in the United Kingdom.. At least I can think metric and imperial interchangeably, whether its...
  4. S

    Need to figure out what yeat this MHF Tractor is

    I have a MF 575. MF produce a workshop manual, which covers the 500 range, When needed, it has different paragraphs for different models. Obviously, living in England, I do not know if it available in the USA.
  5. S

    1967 MF 135 Diesel Wont Start

    My FE35, 4 cyl diesel had similar problems. There is a small 'wire basket fuel filter' where the fuel pipe from the filter enters the injector pump. It is not mentioned in the manual or parts book. When I cleaned it out, the problem was solved. Luckily, I was told of its existence by an old...
  6. S

    drawbar bolt size

    Agrilineproducts.com list both 5/8" x 2 3/4" and 3/4" x 2 3/4" studs for the MF 135, the thread into the tractor is UNC and the thread for the nut is UNF.
  7. S

    Running Boards foot rest replacement

    The damaged, rectangular one is for use with safety mudguards, i.e. the mudguard extends down to the running board. The tapered one is for use with the earlier , non safety mudguards, which are symmetrical, when viewed side on.
  8. S

    TO-35

    In the UK, most tractors have the starter safety switch on the hi - low gear selector, so the (large) gear lever can be in gear, while the (smaller) hi - low leaver is in neutral. At least this is the case on my Ferguson FE35, my Massey Ferguson 35X , my MF 575 and my Ford 4000.
  9. S

    MF135 restoration.

    Jim I have had the same problem with the lift arm handle fouling on the ROPS on my FE35. However, in practice it is not an issue, lower the lift arms before adjusting. If I have a plough on the arms, I cannot turn the lift arm handle when the weight of the plough is on the arms. If I lower...
  10. S

    reinstalling banjo

    If it leaks, check the thickness of the copper washers. I had to replace the fuel filter housing on a FE35 23C 4 Cyl diesel. On reassembly it leaked at the banjo joint of the fuel return line to the tank. Eventually, I discovered that my replacement copper washers were thinner than the...
  11. S

    Ferguson FE35 Glow Plugs

    Thank you for your comments. Today, the replacement glow plugs arrived and I have fitted them. The tractor started very easily. I think that I had been over cooking the plugs, i.e. Having them on heat for two long. Originally I was advised to give 3 X 10 seconds bursts of heat, with 5...
  12. S

    Ferguson FE35 Glow Plugs

    Ideas please. I have a 1957 FE35, 4 cylinder diesel, UK built (where I live). In 1997, shortly after getting it, I had an exchange cylinder head fitted, with a glow plug for each cylinder. This transformed it's starting ability. This modification was a factory option for cold weather areas...
  13. S

    Trailer ramp assist devices.

    I have two 8ft aluminium ramps for my trailer, usually used for loading a Ferguson 35 tractor and plough. Much easier than the steel ramps on the previous, stolen, trailer. I say to people ' you curse once, writing out the cheque and your back says thank you every time you use them'.
  14. S

    quick hitch

    The simplest way is to have a tractor for each implement, saves the bother of hitching and unhitching!
  15. S

    MF FE 35 X MF 35 4 cylinder Dash Installaation

    I have both a 1957 Ferguson FE35 and a 1963 Massey Ferguson 35X with Standard 4 cylinder diesel and Perkins 3 cylinder diesel respectively. The dimensions of the dash and bonnet are the same. I find that they fit together much better if the two bonnet clamping pins are used, rather than if the...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top