(800) 853-2651
SHOP NOW

Recent content by slick1

Yesterday's Tractor Forums
  1. S

    G1000 Club

    We bought a new G1000 in 1965,but I never saw anything like that. But we bought a new A4T in 1973, and we did get a small plastic card with the serial # on it and stating something about joining the Minneapolis family. It looked like a yellow credit card.
  2. S

    parts for sale

    Hapco in Terrehaute Ind. has a 301 Int. crank stroked to 5" for sale for around $900. Owner couldn't afford to pay! Posting for a friend.
  3. S

    Moline G6 weight

    I didn't notice the inside one. I think those bigger ones are#550-600 each.
  4. S

    Moline G6 weight

    Moline operators manuel says "dry weight LP 7650. There are several sizes of those weights. Yours look to be about#350 each.
  5. S

    Pics-Doug Meissingers G-1000 MM Super Stock Puller

    I am an old time MM fan. If you see black smoke coming out of it ,and it is running with the best of them, it is not an MM engine. Decals and paint do not a "true" tractor make.There are many of those fake MM's through the central USA.
  6. S

    removing clutch from moline gvi

    If you hit the end of the clutch shaft with a big hammer a couple of times after removing the nut and washer, it usually pops the plates loose,or at least makes the puller pressure much less.
  7. S

    G1000 Vista clutch pilot bearing

    The manual says to install the seal lip edge towards the crankshaft. There is also a thin metal ring that goes in the flywheel outside the bearing(compensation ring).
  8. S

    MM Collectibles Auction In Colorado

    The manual says to install the seal so the lip edge is toward the crankshaft. There is also a small ring of metal that goes around the outside of that bearing in the flywheel hole( compensation ring).
  9. S

    G1000 Vista clutch pilot bearing

    There is also an oil seal that goes in the flywheel. There is oil coming from the rear lube pump for the torque that also lubes that bearing,thus no need to be sealed. That is the correct bearing from what I see.
  10. S

    Impco Model 100 Throttle body part #

    There are 4-5 different butterfly diameters on the 100. I think they go from 1" to 2". If you let me know which size you have, I have all the part #'s,or I could give you all the #'s,by photographing the whole page of the part's book.
  11. S

    585 transplant g900

    You will have flywheel problems,as the 585 in a 2-150 is likely a one piece rear main seal design. You will need to find a one piece seal flywheel that will mate up to the G900 clutch and transmission .
  12. S

    403 rods

    yes I have several. $25 each delivered to your door USA only.
  13. S

    MM Prairie Gold 1 Paint

    I would be interested in your paint codes. Very nice looking color!
  14. S

    UB Starter woes

    I have starters available. $125+shipping.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top