(800) 853-2651
SHOP NOW

Recent content by slowsmoke

Yesterday's Tractor Forums
  1. F

    F-12 fuel level

    The I-T book says, " fuel level to be 23/32 inch below the bottom of the upper body." But it does not give any information on how to arrive at this figure. Would appreciate hearing some ideas. Thanks, Fritz
  2. R

    172 diesel engine balancing ?

    I was reading some old posts about balancing this engine. How do you balance them aside from the counterbalance? Weigh each rod and each piston? Where do you remove metal on rods and especially pistons? Also do you balance all four pistons or rods to each other or the piston and rod assemblies...
  3. Brendon-KS

    Marker lift rope routing on Deere 8000 drill

    I've got a Deere 8350 with the marker attachment and am wanting to set it up for rope lift. I believe all the parts are there except for the rope - it has the uprights on the ends of the frame with the porcelain insulator guides and remnants of frayed rope tied into the loops on the marker...
  4. B

    Extremely RARE historical photo...

    ...of an early prototype of the "ETD"! <img src = "https://i.imgur.com/4vANMpu.jpg"> (Actually, it's an artist's conception of a ?Lunar construction vehicle from Project Horizon, a 1960 US Army study of feasibility of constructing a scientific / military base on the moon.?)
  5. W

    Came new with a rattle

    I bought a new Hitachi leaf blower online from XXXX tools. It arrived quickly and looked good' Upon inspection there was what sounds like a loose bolt inside the case of the blower. Lean it right, the bolt rolls right, left and it returns to the left. I'm not sure what to do. Open the case and...
  6. R

    Year make and model

    I just bought a Massey Harris tractor, the man told me it was a 1956, but im not sure, i need to know because i would like to get the manual on it
  7. 3

    Can't believe that happened

    Last disking job of the year. I was finishing up. I stopped to close a gate. The tractor stopped. I thought I killed the motor backing up to close the disk. All I could do was walk to the truck about a block, and a half way and get my battery. The tractor started and stopped. I was on a incline...
  8. 1

    9600 John Deere opinions

    Just wondering what the opinions are on 9600 John Deere combines. I'd like to upgrade and want to keep a walker style combine.
  9. W

    Traditional FKarmer

    Still interested in your MC ro tary scyth excatl;y wh;ere i n VA/ I have /no idea why message is sh' ow ing thi s way
  10. G

    Tractor Show

    Happened to see this ad and thought maybe some of you New Englander's might be interested. https://newlondon.craigslist.org/grd/d/straw-hollow-antique-engine/6651536435.html
  11. W

    2355 clutch slipping when warm?

    Hello I?m new here but recently read of a similar issue that I?m having through this forum. I just purchased a JD 2355 and when it gets warm from pulling for an hour or so, it begins to act like clutch is slipping especially in higher gears. No smell of hot or slipping clutch though? Any...
  12. R

    Drain elbow leaking on new tub

    Got the Maax tub in and put plumbers putty on the strainer body(4 times & still leaks) with drain elbow gasket underneath tub. Can't get to stop leaking, no matter how tight it is. Any ideas to stop leaking. I used standard plumbers putty.
  13. glennster

    240 u governor spring question

    just got the 240 u out of the shed to get it ready for spring. ran it around a little and it was fine. went to re-start it and the governor spring that comes off the throttle control slipped off. looks bent. i just ordered a new one from this site. can i just pull the front cover off the...
  14. 4

    IH27V mower

    I need to get the driven belt pulley off to replace the wrist pin stud that holds the pitman arm on. The pulley is a full circle counter-balanced pulley unlike the one shown in my book that has a flat part. The shaft end shows through along with the end of the tapered key. Spaced around the...
  15. L

    Piston Stuck

    I finally got out in the garage today to start putting my project 3400 back together. The plan was to get the head put on today and check compression. Once I got out there I realized one of the pistons was not moving when trying to turn the radiator fan. I sprayed penetrating oil around the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top