Recent content by snafflekid

  1. S

    4600 SU sat for 2 years, what do I need to check now?

    I tried starting the tractor today and it was acting the same. It would start with a choke, run for about 10 seconds then die. Then I put 3 gallons of gas in the tank. The tractor started up and runs without dying. Hmm
  2. S

    4600 SU sat for 2 years, what do I need to check now?

    The coil went bad as you suggested about 8 years ago and was maddening to figure out the source of the problem. The tractor would just die randomly usually far from the barn only to start back up when I showed it to my father :lol: As I recall the tractor died suddenly like the key had been...
  3. S

    4600 SU sat for 2 years, what do I need to check now?

    The coil went bad as you suggested about 8 years ago and was maddening to figure out the source of the problem. The tractor would just die randomly usually far from the barn only to start back up when I showed it to my father :lol: As I recall the tractor died suddenly like the key had been...
  4. S

    4600 SU sat for 2 years, what do I need to check now?

    It's me again! I had the flat tire with the leaking ballast fluid. What a mess, and of course the floor jack was bad too and would not lift the rear end. So, I swapped the valve core with the valve stem in the down position and of course lost quite a bit of fluid from the flat tire. As it turns...
  5. S

    Oh boy, tractor tire is a mess

    and a followup question... I mostly mow with a rotary mower attachment, and some light grading of the gravel road. Is the ballast fluid important? I should also mention that I am sometimes mowing on hillsides with a 20% slope, but I usually attack the hill straight up and down. This post...
  6. S

    Oh boy, tractor tire is a mess

    Thank you for the really good information. Now it seems likely that the valve failed. I figured the rims were hopeless. I see bubbling rust on the rims in spots and I thought that maybe the rims had rusted inside out in places. It could be just surface rust. Clean the rust with Naval Jelly...
  7. S

    Oh boy, tractor tire is a mess

    I am back at the farm after 2 years and I found the Ford 4600SU tractor has a flat tire. I am guessing the rims are bad also. I was not sure if there was ballast fluid in the tires but now I am sure. Just wondering what all this will set me back to fix. Do people do this type of tire work on...
  8. S

    Ford 600 runs great for hour then starts cutting out, help

    check out this post by me. http://forums.yesterdaystractors.com/viewtopic.php?t=1171877&highlight= I had the damnedest time with my tractor dying mysteriously. Turned out to be the spark coil. You could check your coil resistance or if it is old, just replace it.
  9. S

    Ford 4600SU pto seal leak

    Got the PTO cover back on. Drained the little bit of axle fluid left. I found an interesting blob of metallic paste on the magnetic drain plug, glad I decided to check. Then went to refill the rear axle fluid and could not get the stripped allen head plug out of the inspection hole (haha! Of...
  10. S

    Ford 4600SU pto seal leak

    My local New Holland dealer installed the new seal for me. It looks a lot different. I will post pics. Who knows maybe this will help someone else :) Now the rear axle fluid inspection hole is a problem. It has a plug in it that uses an allen wrench to remove. Looks kind of worn from the...
  11. S

    Ford 4600SU pto seal leak

    The PTO shaft is polished where the seal goes but I do not feel a groove. The tractor has 2000 hours on it.
  12. S

    Ford 4600SU pto seal leak

    I have another question also. How do I get the seal out to replace it? That seal does not want to pop out. something seems to be holding it in place
  13. S

    Ford 4600SU pto seal leak

    Hi all, I pulled off the PTO cover to start finding the source of a PTO leak. I have read about the trouble with the thrust washer dropping blocking the re-entry path of the shaft. So before pulling out the PTO, maybe the fix is not so bad. If I only replace the gasket that sits inside this PTO...
  14. S

    independent PTO how does it work?

    I am curious how this independent PTO works. I thought that I needed to keep the engine speed at 1800 rpm to have the PTO spin at 540 rpm. That seems to be what the decals indicate on the tractor. I am reading the repair manual and it says "reduction gearing in front end of transmission housing...
  15. S

    cracked my exhaust manifold

    New manifold was $50 aftermarket from Turkey. Made next to the Wal-Mart frying pans I guess?
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top