Recent content by SouthNoack

  1. S

    IH1486 IPTO input shaft excessive end-to-end play

    Talking with Joe, he says very likely my problem is that I have the couplers on the extension shaft backwards i.e. the flush part (with the gear teeth to the edge) of each coupler need to face each other on the extension shaft with the protruding lip w/o teeth for 1/4" extending outward from the...
  2. S

    IH1486 IPTO input shaft excessive end-to-end play

    Hmmm, there wasn't anything like that when I took it apart. There are literally 3 components involved: 1) The shaft which has a different number of splines (and diameter) at each end, 2) Smaller coupler in front connecting the shaft to the rear of the transmission, and 3) Larger coupler at the...
  3. S

    IH1486 IPTO input shaft excessive end-to-end play

    Hello, Just replaced the clutch pack in the dual-speed IPTO unit on my IH1486 (it's the late-1086 dual-speed unit) as I had it out of the tractor replacing the draft tube and seals (lots of fun getting the torsion bar pressed-out of the old draft tube I must say) and after re-installing the...
  4. S

    Barring a DT436

    Thanks yall for your responses, much appreciated. Engine turns very (almost too) easily with a BFSD on the ring gear through the inspection hole. I thought it would roll a lot harder than it does. ;-)
  5. S

    Barring a DT436

    Is there a barring tool available for 300/400 series engine to roll the crank for valve adjustment? I've seen barring tools available for DD engines but I cannot seem to find anything available for the 300/400 series engines. I've got a 1486 with the DT436 which I would like to adjust the...
  6. S

    Removing front axle front bolster pin

    Thanks for that, I think it needs to be steel too as I don't think the bronze will hold-up and certainly would need to be a tight fit as any slop will wear quickly and get back to where I am now. Likely will need to take it to local machine shop and have it center bored to take a steel bushing...
  7. S

    Removing front axle front bolster pin

    Update: Finally got the front pin out. Ended-up removing the front bolster entirely, followed-up with a big socket and sledge hammer managed to convince the pin to come out ;-) Rear pin hole in bolster casting is worn to 1-7/16" round whereas the new pin is 1-1/4" OD. I'm planning to try...
  8. S

    Removing front axle front bolster pin

    Thanks guys, unfortunately after another evening of heat and beat, looks like it's gonna hafta come off entirely for a press. And unfortunately I didn't remove the loader before I started as I thought I could get that pin out which means putting it all back together as it was just so I can get...
  9. S

    Removing front axle front bolster pin

    Hello, I'm in-process of replacing front axle on my 1486 and having a time trying to drive that front bolster pin out. Service manual says to drive both pins in-ward, rear pin is so loose it'll fall out of course but that front pin, it's not budging. Yes the lock pin has been removed and I can...
  10. S

    1486 with dual-speed IPTO and without TA

    Thanks for replies, much appreciated. It is good to finally find an active forum for Red Iron. Re TA I dunno I have read about a lot of issues with em, mine doesn't have it, came factory that way and yes the tractor is a bear to shift most of the time, trans brake is obviously worn-out, and...
  11. S

    1486 with dual-speed IPTO and without TA

    ​I have a 1486 which has dual speed IPTO i.e. both 1000 rpm and 540 rpm shafts and it also does not have the TA (which is a good thing of course). In looking through the service and parts manuals I have it leads me to wonder if I have an oddball 1486 as the manuals state 1486's were not...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top