(800) 853-2651
SHOP NOW

Recent content by splitter

Yesterday's Tractor Forums
  1. J

    IH 1 bottom plow parts needed

    Good evening, I ve got what I believe is a B192 1 bottom plow for my Farmall B. However, I do not have any of the connecting assembly. Anyone on this forum have these parts forsale or know where I might find them? Thank you This post was edited by JD70/B on 05/31/2023 at 08:15 pm.
  2. R

    1965 Ford 3000 Diesel not firing

    Hi. I'm new to the forum. Have been buying parts on here for this tractor. It was my grandfathers who used it to plow the fields and plant cotton back in the day. It has been sitting for over 20 years outside. I put all new fluids in, freed up the wheel, new starter, new wiring, etc...
  3. L

    j schwiebert

    j I need a pic of how to mount a loader on a 550 it is the older round pipe type thanks for your help
  4. S

    John Deere 1240 planter help needed!

    So I bought this planter on the assumption that it was the plateless version. After buying a plateless manual i realized it is not a plateless planter. Does anyone know the gear sprocket combination that go with what size plate? I figure the 24 cell plate would turn slower so I could just go for...
  5. S

    Ford industrial diesel

    hi, Im a 16 year old with a 77 f250 with the 351 Windsor in it. The problem is that I'm getting about 5 miles a gallon in it. My buddy's got an 72 international pickup I'm planning on swapping engines with. His grandfather put a ford 254 industrial 4 clyinder diesel in it. I'm wondering where I...
  6. S

    ford 9n no oil pressure

    So I rebuilt the engine. New rings,con rod bearings, carb, electric system and gauges. This will be the 8th time dropping the oil pan so I'm really hoping to avoid it. As it goes I had the tractor running for about 3-4 hours 3 weeks ago. I had relatively low oil pressure 10-15 lbs hot. This...
  7. S

    ford 9n thump when starting

    Hi I'm rebuilding an ford 9n. I'm 15 doing this as a winter project but winters over so its gotta live :). I put a new starter, rings, valves, rod bearings,manifold, muffler, entire eletrick system on it new carb to. I've got 95 lbs compression through the board. 3 weeks ago I had it running...
  8. S

    beefalo calfs

    Does anyone know how much beefalo calfs cost in Michigan?
  9. S

    case ih 1494 cold starting

    Tractor runs good once its started. It sat for the last 15 year. I put about 150hrs on it last year but it could still be being broken in from the sit. It only has 800 hrs. When I try to start it cold it smokes out our barn so I imagine the engines just to cold to catch
  10. S

    case ih 1494 cold starting

    Hello my grandfather was diagnosed with Alzheimer's 3 years ago. I live on 160 acre hobby farm that without him was left it to me to maintain until I go to college. I'm having no luck with his caseih 1494. It runs amazing. When it decides to start. My question is is there a glow plug setting on...
  11. S

    ford 9n compression problems

    Thank you all for the replys. Took everything apart and down to the block again and found out that the pistons were .003 oversized. Can you find rings easy online? The guy I bought it from really screwed me over. Paid 1200. Guy said all it needed was a battery and a carburetor. He had a bag...
  12. S

    ford 9n compression problems

    I will check for cam to crank markings to see if they are lined up on Monday. Thank you all for the advice
  13. S

    ford 9n compression problems

    Is there any test where I can pump air into the cylinder to see if my clyinder walls are to warn to give good compression?
  14. S

    ford 9n compression problems

    Is that for roto valves. I set the valves to the roto valve specs in fo4 then put gas on top of each valve and counted 3 min with no leaking
  15. S

    ford 9n compression problems

    No it will not run I had it running on 1 clyinder before I reringed it so the timing is right
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top