(800) 853-2651
SHOP NOW

Recent content by stroker88

Yesterday's Tractor Forums
  1. S

    Chrome plating blocks and crank mains

    can you say hydrogen imbrittlement? chrome bore requires iron rings. iron bore holds more lube, also can be honed and resized. chrome on bores and crank journals are usually only about .001 thick. and prone to flaking.
  2. S

    CRANKSHAFT BALANCING

    some come in real easy. others are a real pain. when you get them real close, and do the whole rotating assembly. they are amazingly smooth. the throttle is like a volume knob. no sensation just more noise. most people don't even realize the effect.
  3. S

    CRANKSHAFT BALANCING

    15 years of truck mechanic, 24 years of automotive machinist, and not ready to quit for a while yet.why do you claim 2 grams? we claim less than 1 and are usually not satisfied till it's below a half.
  4. S

    CRANKSHAFT BALANCING

    by 2 grams. do you mean 2 inch grams?
  5. S

    Aluminum rods for John Deere 2 cylinder?

    generally an aluminum rod is about twice the section thickness of steel.
  6. S

    Aluminum rods for John Deere 2 cylinder?

    a real automotive machine shop can recondition them. i've done them more times than i care to remember. my question is with the added size of an aluminum rod how do you plan to clear every thing. you are correct they have a rather short life expectancy.
  7. S

    70 Oliver Block- Upgrade?

    where are you located? do you know where the tractor came from?
  8. S

    oliver 66 frt end ???????

    john is right if it is for a 66 the casting # begins with a L.
  9. S

    77 PTO weight??????????

    100 lbs.
  10. S

    oliver 77-770 bore

    i don't think there is enough room for them in a 77. that is one of the sleeves we have modified and used in the 88.
  11. S

    oliver 77-770 bore

    we were 4.125 x 5.75 with water.
  12. S

    Oliver 66 ground speed?

    will vary depending on what ring & pinion you have. also if you have the normal or special 1st gear.
  13. S

    Oliver 66 Front End

    I don't think the spindles are the same size. If it was doable we would have done it.
  14. S

    Oliver 66 Front End

    yes it will. weight loss depends on what hubs the 77 has. i know most of the 77 & 88"s around here run the 66 front.
  15. S

    Scatter Blanket

    it doesn't matter they are for automatic transmissions. they won't stop a clutch, pressure plate, or flywheel. i saw one go on a pick up, part of the flywheel went through the dash windshield and about 100 feet in the air. fortunately it came back down on the track and didn't hit any people...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top