(800) 853-2651
SHOP NOW

Recent content by Tater Head

Yesterday's Tractor Forums
  1. T

    change tires or quit pullin

    Nothing critical about it. You might get 100 different responses to your post, but the bottom line is that you're either going to pull or not and your going to do what ever YOU think you want to do. Not what somebody else says, so don't whine about your tires. Just figure out if you want to pull...
  2. T

    change tires or quit pullin

    What"s your address/ I"ll send you a Whaaaaaaambulance! Most pulls go by the natpa tire chart in divI and II classes and have been that way for quite a while. Maybe some local town pulls don"t have any tire limits and that"s fine too, but you can"t have it your way all the time either. First...
  3. T

    IH 301

    If it's out of a 101 it sure as h-ll is NOT a 301
  4. T

    460 hydraulics

    Wanting to get rid of all the hydraulics on a farmall 460 EXCEPT the power steering. I have already removed all the controls and valves. My question is, can I block the cast upright where the spool valves bolted on and make that work, or will the pump not drain back into the system causing the...
  5. T

    I couldn't find a sled so..I pulled the house!

    Looks like a non original illegal motor to me!; but; it does match your house,
  6. T

    Ruthann Meyers

    I know who Mike is and have noticed that on most of his posts and replies on here that there is quite an "air" about him. He pulls an old JD and thinks he's more knowledgeable than most. Like I said, I know who he is and you can bet he has no clue he's acting like the idiot he is.
  7. T

    mlpankey

    These remarks are so typical! Every time somebody gets their "bass" handed to them; then right away, sombody's cheating. Want me to send youall a WHAMBULANCE!?
  8. T

    Oil sender location on 263 gas engine

    left back side of the block just above the frame rail. there are a couple of places there to do it
  9. T

    Big Bang Theory - AC

    exactly my point. thank you
  10. T

    Big Bang Theory - AC

    You guys need to stop and read your posts as if you were normal people on here and see just what kind of an impretion you're giving everyone on here that has a real life! Grow up!
  11. T

    Pulling Sled

    Am needing contact info for the Ol' Busch Sled. Thanks in advance!
  12. T

    New Pulling Club In Missouri??

    Near Sedalia, MO
  13. T

    Mechanical TA Troubleshooting Guide

    Then you need to shorten the short ta adjustment rod a little. Be sure not to go too far or you will get a "double shift" when releasing your clutch. If youdo; then lengthen about 1/2 turn untill it quits
  14. T

    1650

    What size are the axels on the 1650 and the key width also? Thanks in advance
  15. T

    Axel size

    Was wondering what size axel the Oliver 1650 has and also the size of the key way. If someone could let me know; I'd really appreciate it. Thank you in advance!
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top