Recent content by thomaskd44

  1. T

    TD 9 forty's D335 where is by pass located?

    I removed the plate with breather. The tube had been broken somewhere before me. It wasn't plugged; not enough to cause any problem. I cleaned it the wire guage, and placed it on the engine. The oils still pours out the back as it did before. I removed the oil filler cap, and no change. When I...
  2. T

    TD 9 forty's D335 where is by pass located?

    This plate, the device, is sitting just between the carb and the oil canister. I will have to remove the oil canister to get to those two bolts. I think what you have said is relevant. I am checking it tomorrow. Thanks again.
  3. T

    TD 9 forty's D335 where is by pass located?

    Thanks again AJ. I have another TD 9 block, and the oil dip stick is the same. The oil fill cap screws down on a stud and seals against the hole -no way to breathe. It has the correct amount of oil. I think it may be that device on the plate. Last night, and today we have experienced much rain...
  4. T

    TD 9 forty's D335 where is by pass located?

    thanks AJ. Oh, there is no oil gauge. The problem is, I don't know where the by pass, or breather is. On the intake/exhaust side of the engine there are two plates -correct. The plate in back of the oil filter canister, in the middle of the plate there is a rectangular piece, and at the bottom...
  5. T

    TD 9 forty's D335 where is by pass located?

    Thanx either way it comes out the same.
  6. T

    TD 9 forty's D335 where is by pass located?

    Thank you AJ. I went to baldwin. I have changed the oil filter -1- a couple of times; however, I am curious as to a bypass. Most all combustion engine have a bypass, so as to relieve the pressure in the crank case. I had replaced the rear oil seal, gaskets, and the engine -at the rear- is stil...
  7. T

    TD 9 forty's D335 where is by pass located?

    Thank you.There is a filter canister; I have changed that filter a couple of times. The plate I was speaking of isin ront of the canister. How is an oil filter a by pass?
  8. T

    TD 9 forty's D335 where is by pass located?

    hello. I have the TD 9 D335 diesel engine. Can anyone tell me where the by pass filter is on this engine. I am unable to find it. Was thinking on the left side as you are looking from the front. There is a plate on the side of the engine. There is a piece of metal and at the bottom are two...
  9. T

    TD 9 WQrong piston siZe!! What now--

    so, in the 40's the D335 had different sleeves. Okay. Thanx
  10. T

    TD 9 WQrong piston siZe!! What now--

    As I have read; The 334.5 (D335) was made from the start -40's- to 1956. At that year the D350 was issued. Now, the one engine I have -perhaps both- are made in the 40's. So, how could one engine have the thicker sleeve, and the other engine have a thinner sleeve? To say the thinner sleeve is...
  11. T

    TD 9 WQrong piston siZe!! What now--

    Thanx AJ As I have read; The 334.5 (D335) was made from the start -40's- to 1956. At that year the D350 was issued. Now, the one engine I have -perhaps both- are made in the 40's. So, how could one engine have the thicker sleeve, and the other engine have a thinner sleeve? To say the thinner...
  12. T

    TD 9 WQrong piston siZe!! What now--

    Would you give where I may find more information on your statement? Thanx I wish to understand
  13. T

    TD 9 WQrong piston siZe!! What now--

    Contacted the person AJ. He has three pistons and they are what I need. The smaller piston. He is looking for some rings. I don't understand; why some people keep stating D335 engine. I wondering if they are talking about an engine in the 60', or 70's on? I know the only engine for TD 9 up to...
  14. T

    TD 9 WQrong piston siZe!! What now--

    Thanx A J. The bore I need is 4 and 1/4. I have learned from you and a few that they made two; 4 and 1/4 and 4 and 1/2. Most all engines 334.5 have the 4 and 1/2. I think it will difficult to find a 4 and 1/4. For this reason I think previous owner put a ring on the piston and went with it. I...
  15. T

    TD 9 WQrong piston siZe!! What now--

    First what you say makes sense. AJ, I just measured this morning, and the one engines' piston's measures 4 and 15/32; the other engine with bad piston measures 4 and 12/32. The cylinders ID, on one engine measures 4 and 17/32; the engine with the bad piston measures 13/32. So, I must find the...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top