(800) 853-2651
SHOP NOW

Recent content by Tim Pennell

Yesterday's Tractor Forums
  1. T

    JD310A interchange with JD310

    Yup, big job, intent is not to swap diff, just transmission. The other machine is fairly low hours and clean compared to mine. Mine had been flopped over a couple times and worn out before I bought it 15 years ago, it did not get prettier with age lol. It has more than earned its keep around...
  2. T

    JD310A interchange with JD310

    Thanks, I see the common denominator of the two machines now so there is at least a chance. Any idea where on the transmission body the numbers are located before I take up the entire floor?
  3. T

    JD310A interchange with JD310

    Well my old worn out 1976 JD310A hydraulic pump has failed............ The rest of the machine is tired, buckets done, lots of cylinders weeping, steering held together with a bandaid, cosmetically trashed, very little electrical works etc. But engine and transmission are solid. . Have a...
  4. T

    International 824 4wd

    Close but no cigar :) Broke down and popped the driveshaft off and removed the flange. Looks like 50mmx80mmx10mm . Ordered one locally from the auto parts store, should be here in a couple days. Lots of crap behind it that looks to be from the dust deflector ....
  5. T

    International 824 4wd

    I am after dimensions so I can match it up to a local supplier in Canada with National or Timken seals for instance. These numbers do not cross up to anything I have found. 5 years in a parts store so do know what I am up to. Pulling old seal is a last resort as once I do that the machine is...
  6. T

    International 824 4wd

    Lots of those who say they have it don't when they try and get it from Case. I am after dimensions so I can match it up to a local supplier in Canada with National or Timken seals for instance. And yes I used google.
  7. T

    International 824 4wd

    Just picked up a 4wd international 824. Needing the front diff pinion seal dimensions if anybody has access to them. Case/IH dealer says not only is the number and change up number obsolete but case does not have the dimensions available. Part numbers I found are 3134317R1 and 3216436R1...
  8. T

    BrushHog for TO35

    I have a 1957 TO35 that I recently purchased and tow a woods CO-80 brush hog with flail blades. Works just fine, it is a drawbar tow pto driven setup. The woods mowers are very heavy duty. Mine is 80 inches wide. Some hilly ground but mostly level. I have cut grass that was as tall as the...
  9. T

    electrical question

    Best solution for the glow plugs is a heavy momentary on push button switch, only on when you hold it in, 15-20 count and you are good to go. Did this on an old F350 truck works great :)
  10. T

    odd request need 1 main bearing .010 Case David brown 885

    I have two complete bearings here part number K928540. Not sure what undersize that is, perhaps you can check that out from the part number. Another number on the box is 163310D that D might be a zero also, hard to tell. Cheers Tim
  11. T

    DB770 Realese Bearing

    Thanks a bunch Bob, info printed for future use. I got lucky and the correct bearing arrived yesterday. My supplier checked the shelf on his old stock and came up with a bearing for a Ford Dexta/JD that fir perfectly. Assembly starts today if it doesn't rain. Cheers Tim
  12. T

    DB770 Clutch Fork Assembly Elmer or anybody else???

    Got one out of the states finally, thanks for asking, up in BC Canada. Cheers Tim
  13. T

    DB770 Realese Bearing

    Hi All, Fixin up the ole 770, dual clutch model. Release bearing arrived, K620153, wrong one, way too big ID at 2.75 inches. Of course the books from the supplier say this is the one. Older book showed a K620182 which seems to cross up to the K620153. Anybody have a different number for this...
  14. T

    DB770 Clutch Fork Assembly Elmer or anybody else???

    Thanks sent them a parts request via the web and will call if I do not hear back. Cheers Tim
  15. T

    DB770 Clutch Fork Assembly Elmer or anybody else???

    Wasn't sure if that one was still good after 5 years but I did send to it as well as posting here. Cheers Tim
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top