Recent content by timberwolves

  1. T

    Help identify disc

    Can anyone please help me identify my disc. I have had it for a while now. Just replacing a few parts bearings, cutters and a half spool. Markings on the spools are as follows DK-50, DK-51 & DK-53. They also have the letter G as well as DK on each spool. Any help would be great. [/img] This...
  2. T

    Missing air cleaner inlet screen MF-65

    Im looking for a replacement air cleaner inlet screen for a MF-65 ?
  3. T

    MF-65 stripped bolt hole drawbar mount

    Hello everyone. I noticed fluid leaking underneath my tractor, the fluid was dripping from the bolts that hold the bracket for my swinging drawbar. After further inspection I noticed a previous owner installed a helicoil type of insert and must have drilled it in to deep. Ugh!. Now what? Can...
  4. T

    Disc Harrow

    We are looking to upgrade our current set of discs, they are 6' wide and are angle iron 3 pt. hitch type. Our tractor is a MF- 65. It currently does not have hydrolics installed but are in the process of installing. We are looking for the type that has transport wheels. What size disc do you...
  5. T

    Massey Ferguson 468 Planter

    Looking for fertilizer boxes and seed hoppers for a Massey 468 planter. Previous owner removed and cut down the hoppers. Any ideas how I can locate the parts ? Thankyou John.
  6. T

    Massey Ferguson 468 Planter

    Looking for some parts for a 468 planter. The previous owner removed the fetilizer boxes and cut down the seed hoppers. Looking to replace these parts. Any ideas ? Thankyou John Figured out how to post a pic.,but not how to delete this post.
  7. T

    Lower link wrist action ball ends

    Does anyone know how to rebuild the lower link wrist action ball ends on a MF-65 ? The spring is missing and the link does not lock in. I purchased a lift arm lock pin kit and it comes with 2 washers, spring , bushing & 2 what looks like press in pins ? Thankyou John
  8. T

    Remote Hydrolic Valve Kit

    I have a MF - 65 with a continental 176 gas engine. I would like to add a remote hydrolic valve kit to it. I am not sure if I would need a single or a double spool kit. The only things with hydrolics I would be using is a set of discs to go from transport to the field with a single ram and a log...
  9. T

    gas cap

    OK so it built up vacuum, not air pressure. What could cause vacuum to build up. The gas cap looks kind of new but I dont know. I dont see a vent hole on it either. Any ideas?
  10. T

    gas cap

    After brush hoggig with my MF-65 for a hour or so, when I checked the level of gas in the tank it let out alot of air. Could my gas cap be bad and cousing pressure to build up in the tank ? Doe the cap have to be vented. If so any ideas on what cap to use ? Thank you John
  11. T

    MF-65 Generator to Alternator conversion

    rvirgil_KS Thank you for the information. Just a few more questions if you dont mind. Does it matter what wires go where. On the side of my alt. there is two spade conectors, and one red lug on the back. In you diagram it is listed as #S 1&2. Does the orientation of the alt matter. How do...
  12. T

    Fuel Bowl

    Hey guys I am installing a new fuel bowl assembly, what kind of compound if any should I put on the threads as this threads into the bottom of my tank. It is a gasoline tractor. Thank you John
  13. T

    O/T Central A/C in Basement ?

    I am currently finishing my basement I have central a/c in my house. Should I expand the systyem to my basement. Anyone have any knowledge any hvac guys can help me ?
  14. T

    MF-65 Generator to Alternator conversion

    Thank you for the info. I guess my alt. is wired wrong . I will re-wire it using the directions you sent me. What is the diode or idiot light for ? Does the delco 10SI have a low rpm cut in , or do I have to rev up the RPMs ? Thank you John
  15. T

    Rust in gas tank

    I was getting alot of sediment and rust in the sediment bowl from my gas tank. I brought my gas tank to a local radiator to have it boiled out. I payed $ 40 to have this done. The problem is that it still has surface rust on the walls. Should this have come out with the boiling out process ...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top