(800) 853-2651
SHOP NOW

Recent content by Tireboy

Yesterday's Tractor Forums
  1. T

    806 Orval Redenbacher

    I have herd a story about several 806's pulling grain wagons of shelled popcorn from the field to the processing plant. Does anybody know about this?
  2. T

    New Idea corn picker

    Thank You for the information. I'm planing on making the disc's out of conveyor belt. Got all winter to do it.
  3. T

    John deere h-1 plow substitute???

    Contact Tyler Bucheit at [email protected] he deals in John Deere plows and parts.
  4. T

    New Idea corn picker

    Does anybody what the new diameter is of the rubber husking roll is for a 323 New Idea corn picker?
  5. T
    Sold

    For sale Gibson H

    $1,700.00
  6. T

    John Deere A oil question

    I have a A operators manual in front of me and it reads below 10 degrees F. S.A.E. 10-W, 10-32 20-W, 32-65 30-W, 65-90 40-W, Above 90 50-W. I would say they were quite concerned about viscosity looking at that chart. If you use a multi-grade oil the first number is the real viscosity of that oil...
  7. T

    John Deere A oil question

    I have a A operators manual in front of me and it reads below 10 degrees F. S.A.E. 10-W, 10-32 20-W, 32-65 30-W, 65-90 40-W, Above 90 50-W. I would say Mother Deere was quite concerned about viscosity looking at that chart. If you use a multi-grade oil the first number is the real viscosity of...
  8. T

    1950 John Deere A flywheel out too much

    That is foot pounds also run it a while and re-torque it.
  9. T

    Choose Your Tractor

    Went to the Nebraska test book for 1950 the IH TD24 was top dog for horse power but realistically at 40,595 pounds it would hard to hall. I'd settle for a John Deere R.
  10. T

    98 454 manifold studs

    Why did you replace your studs did they rust out or break? I have a 98 454 the front studs on both sides broke off. The one side broke five or six years ago. Haven't any exhaust leaks yet not going to do anything till they do.
  11. T

    GMC farm trucks with Detroits

    Where I worked we had a GMC from the early fifty's it had a 4 71 two valve head. Today it would be a dog but compared to a gas motor of the day it was not that bad. I ended up with the motor it run a sawmill just fine.
  12. T

    compression release on A

    You say you have to much compression. The only way you could to much compression to make it hard to turn over is some one put in high compression pistons. There is one other thing to make it hard to turn over is if they shimed the rod bearings a little to tight when they rebuilt it. If you have...
  13. T

    Big Snapper Infomation

    Can anybody tell me what year this mower is? I can't find much of anything on this old girl.
  14. T

    David Bradley

    I have got a David Bradley walk behind 917.5752 serial # 256 with out a engine. With what research I have done the early one's have a model N Briggs and the later a model 6. The question is which one should I have?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top