(800) 853-2651
SHOP NOW

Recent content by toddsmith23

Yesterday's Tractor Forums
  1. T

    Case 320 Wheel hub

    Hello folks - One of the previous owners of my Case 320 put a terribly wrong front wheel hub in lieu of the correct one. My guess is it was off a old chevy or ford that was sitting out in a field somewhere... still has the brake drum attached... sigh Needless to say, i'm looking for a...
  2. T

    WTB: Need '46 Cat D2 Fuel Injector

    Hey everyone - I found 4 injectors in Mn that should be arriving soon. Thanks to all for looking. -TS
  3. T

    WTB: Need '46 Cat D2 Fuel Injector

    Do you have a D311 or a 3400 in that 212? My guess is it's a 311 since it's a '52. If it's a 3400, then it'll work. I really appreciate you looking. -Todd
  4. T

    WTB: Need '46 Cat D2 Fuel Injector

    Hey folks - 5J8143 is in dire need of a working or parts injector. She has a broken nozzle orifice and hoping to get the injector replace or repaired soon. Any help in locating an injector would help a ton!! D3400 engine - 3 3/4 bore Thanks in advance!!
  5. T

    Sourcing '58 Case 320 FEL & Hoe hydraulic seal kits

    Thank you! Didn't think about the obvious. Numbers would be great
  6. T

    Sourcing '58 Case 320 FEL & Hoe hydraulic seal kits

    Hello - Well the old girl works like a champ, but she's leaking hydraulic fluid everywhere. I need to tackle repacking all the cylinders but can't seem to find a good source for seal kits for the front loader and backhoe cylinders. Any thoughts on a good source? Regards -T Smith
  7. T

    My 'New' 320

    That sounds great! I'll PM you for details.
  8. T

    My 'New' 320

    Thank you! But really the thanks belongs to this forum as well as service & parts manuals. There's still an awful lot to do, hydraulic leaks, i might have a leak between the engine & torque tube (either that or i over filled it.) and so on. Power steering doesn't work, but i can live with that...
  9. T

    My 'New' 320

    I've found parts from Steiners & Roberts Tractors in Port Townsend, Wa. Roberts is a tractor salvage, i've bought engine parts from them. Let me know if you need contact info.
  10. T

    My 'New' 320

    Thanks to Joe and many others helping me out with my 'new' 1958 320. I've done some repairs, but mostly maintenance at this point. I do believe it's been neglected for many years, hopefully not too much damage done. Still a fair amount to do yet. lots of hydraulic leaks (all cylinders) and so...
  11. T

    '58 320 Steering

    Not yet, but i will as soon as i get it all back together. Getting close
  12. T

    '58 320 Steering

    The problem i'm having now is, i can't get the cam off the shaft. I've tried penetrating oil overnight, heat (not so much to risk damaging seal), 2 jaw puller and etc. Not budging at all. I'm starting to think i may need to pull the steering arm off the bottom then lift the entire assembly out...
  13. T

    '58 320 Steering

    Should i be using 140w in this, or something else. My service manual doesn't show this component... hmmm
  14. T

    '58 320 Steering

    Question: what's the best way to remove the cam? I don't want to do any unintentional damage. I would think it should slide up off the splines... it's pretty rusty, i gave it a couple squirts of penetrating oil. Also, should i use a punch and drive the posts out, or would a press be better...
  15. T

    '58 320 Steering

    Hello all - As part of other maintenance tasks, i pulled the steering cam cover off at the direction of Joe (Wa) to inspect the steering cam and cam posts. All of you know more about this than i do, so i'll just point out the obvious and say that i'm lucky to have a 3 post steering. 2 of...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top