(800) 853-2651
SHOP NOW

Recent content by tom schwegel

Yesterday's Tractor Forums
  1. J

    Cant find parts for my 4610 4WD Transmission anywhere.

    Hi Guys. I really hope that you can help me here :!: I have a Ford 4610 4WD with the following id: SN: BA19482 Model: DA314D Unit: 4GO5B Engine: 788394 4GO2 Transmission: 4F25B I found a repair manual, but it does not cover my transmission, none of the pictures looks correct. I...
  2. T

    Tractor pull

    Antique tractor pull this Sunday august 27th registration at 9 pull starts at 10. We have a stock class 3500-8500, a 15% over stock class, and an enhanced class! This is located in ira New York. Just south of the ira four corners. For more information look us up on Facebook at plan b pullers...
  3. 2wheelgnnr

    Cyclops Headlight? not standard equipment

    Had an 8n now getting a 53 jub. in the beginning of my research I saw alot about a large headlight smack on the front hood of tractor. naa models looked like...now that I know more It appears they were not standard equipment on those tractors.... was it accessory or what? wanting to know...
  4. A

    Trailer Plug wiring

    Probably other places to ask this question but this is an every day site for me and lots of knowledge here.I just purchased a 2005 F-350 with dump bed. It has the round pin connector and no brake controller. I have ordered a connector for my Tekonsha controller so that should be straight...
  5. B

    WC transmission change

    Hi! I've just found out that I have a gigantic crack in my WC's transmission housing. Water must have gotten in there an froze n broke the casting. I have looked at the service manual and it gives a vague description on how to pull it apart, and looks pretty straight forward. But I do not want...
  6. C

    Stabilizer Bar Length

    Gents, I'm trying to get some stabilizer arms for my 8N and the ones I picked up from TSC (31.5" C-C) are too long for my tractor. The distance from center of the front stabilizer pin to the center of the pin on my brush hog is approximately 28-1/4". Any ideas on what might be wrong?
  7. B

    Rocker Arm Rebuild

    When I pulled my rocker shaft apart to clean up, I noticed the shaft had lost the locating pin at some point in time, and the shaft looked like it had spun around a little. I've tried to find information on the pin and how it fits, also what its made like and how can I make one to replace it...
  8. S

    Paint for a Case 350

    What paint should I use YT has Desert Sand. Case say to use desert sunset. or are they both the same????
  9. T

    8n lever

    I just bought an 8n, what is the little lever under the seat on the right side do?
  10. T

    1066 fuel pump timing

    The fuel pump was removed from a 1066 turbo. I have the piston at top center. The pump has a pointer and mark. What about the timing advance marks on the flywheel ? Are they for a gas engine ? thank you..
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top