(800) 853-2651
SHOP NOW

Recent content by tonyaandralph

Yesterday's Tractor Forums
  1. 6

    1927 Fordson

    I picked up this 1927 Fordson not to long ago. Serial 722404. I would like to start working on it here soon. Just was wondering if there is anything I should be aware of that could be a problem area. It is not stuck. The person I got it from didn't know the last time it ran. Manifold is...
  2. W

    cockshutt injector work needed

    Any one doing injector work on older tractors. Do not need real quick, however do not want to wait till spring. Local diesel shop. A big company knows nothing about older injectors and have to charge very high. Currently have two cockshutt pumps at dieseltech. He does not want injector work...
  3. sammydwm

    flail chopper

    Have an old Gehl that has pretty much been used up. Was using it as a brush hog with the back flap open but the auger fills up and throws the chain. Then it takes lots off power to cut as everything stays in the flails till it's chewed up pretty fine. Has anyone ever removed the auger and its...
  4. C

    J.D. 1010 - RU29075

    this tractor needs a hydraulic pump drive adapter gear. T14421. Anyone have one or know where I can get one ? Thanks in advance.
  5. B

    JD 820 Pony issues

    Ive managed to get diesel engine to run, starts very easily but does smoke a little but might improve with running. Im having issues with the pony motor, I fitted new coils, points, condensers and spark plugs and spark plug leads earlier but had carburation problems. I think carb is doing...
  6. J

    9N Conversion 6V-12V

    This message is a reply to an archived post by Nate Ela on February 17, 2010 at 13:08:32. The original subject was "9N Conversion 6V12V". Is the voltage drop installed on many of these tractors primary purpose to provide a "safety" to protect the original 6v gauges and ignition components? I...
  7. J

    4230 Hydraulics low flow UPDATE

    My 4230 with syncro trans has been a bear to trouble shoot. It has good pressure on the high side but, seems to be low flow. I called the JD tech and they tested it for me. Low side clutch pressure is low at 118 lbs. Checked pressure value out and cant find a problem. So Whats next do I...
  8. S

    message

    sent a few questions, never got any come back. a'm I doing something wrong? Smokey
  9. S

    Tractor won't run after jumping

    I have a 58 MF65. It needs to be jumped in order to start, but when you remove the cables it will die. Any ideas what might be causing this.
  10. A

    Oliver Tractor Tools

    When a new Oliver tractor was delivered did it come with some special tools or wrenches that came with the tractor? My 88 came out in 1949 and I was curious if there had been special wrenches or tools that came with the tractor. If they did does anyone have pictures?
  11. L

    For Zane

    Hey Zane did I misunderstand your reply to Lisas problem with hyd lift piston on 1-28-14. You said to just drive it in and it would work fine? I know as a Guru you know whats what but to force it in it just struck a cord with me when I read it? Have not done one myself what would be the normal...
  12. L

    Cork screw log splitter

    This fall we picked up a pto driven cork screw log splitter. However the pto turns the wrong way on the 8n's so it won't bite into a log. What would this work on? We bought it at an auction with the intention of using it on an 8n so now till we find way to use it, it's worthless to us. (I...
  13. F

    Injector pump rebuild?

    What makes a rebuilt pump so expensive? How hard is it to do-it-yourself? Just curious on the answers. I do have a problem on my 3300 diesel when I try to pull the throttle back. When I do, I must pull back very slowly or else it will shut off. I assume this is a problem in the pump. For now I...
  14. N

    V8 Pullers Custom/Simpons Question/Opinions needed

    Looking for some insight. I want to build a V8 puller and I have two platforms to choose from the Standard Farmall M, or I was thinking of using a Custom Tractor. For those of you unfamiliar it used an inline 6 chysler industrial motor with 5 speed new process trans and 2.5 ton truck rear end...
  15. G

    Thanks to TOH and Zane.

    TOH, My 2N is up and running again with the new hydraulic riser tube fitted with LOCTITE 603 retaining compound. Can hold up the PD15 post hole digger with engine off and closed valve with very very little down creep. :) Also, your live hydraulics is the best thing since sliced bread along...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top