(800) 853-2651
SHOP NOW

Recent content by toolman716

Yesterday's Tractor Forums
  1. T

    MF202 Exhaust Glowing Red Hot - Losing Power

    Thanks to everyone for the tips and suggestions. I finally got back to it yesterday during a break from deer hunting and discussion with several other friends. The FIX was the timing was way off. I loosened the distributor hold down and started her up. I turned it a little bit and what a...
  2. T

    MF202 Exhaust Glowing Red Hot - Losing Power

    Well, no go!!! - Checked Compression - All 4 cylinders 150 PSI - All plugs look a little black, but in good condition, no differences. - Distributor advance weights are fine, springs are fine, move freely as they should. This would rule out a stuck valve. I tried running it again and when...
  3. T

    MF202 Exhaust Glowing Red Hot - Losing Power

    Anybody have any ideas about what is wrong with my MF202??? Last night I rebuilt the Carb, blew out the gas line, drained the gas, and checked the tank for any blockage. The end result was that my tractor seemed to run fine, but then as I started brush hogging I noticed the exhaust manifold...
  4. T

    MF202 Lacking Power

    My MF202 is lacking power when it warms up. I can pull my 5' brush hog in low range 3rd gear, but have to back down to 2nd gear to go up mild hills. After I have been out for an hour it is running hot around 200°- 210°. When I disengage the PTO it starts sputtering and popping, then I have...
  5. T

    Running Rough when hot.

    Changed the coil, voltage regulator, points, and condenser. No real change until I adjusted the carb. I have a Continental Z134. I made a couple of adjustments turning out the Main Fuel mixture screw. The backfiring has stopped and it seems to be running a little better, but it still is...
  6. T

    mf 200 loader

    I have an MF200 loader mounted on my 202 Industrial. The back of the loader attaches to the bottom side of the rear axle housing using the same bolts as the fenders.
  7. T

    Lift Arm Pivot Leaking and Loose

    My MF 202 Industrial is leaking oil at the lift arm pivot and it is loose also. Is there any way to get at the nut to tighten the lift arm pivot without removing the Axle housing? Can the upper plate under the seat be removed to allow access to perform this task? Mike
  8. T

    Running Rough when hot.

    I have an MF 202 Industrial and when it is warm out, about 75-80°, and I'm running under load, it seems to be losing power and the tractor runs rough. I just tuned it up with new points, rotor, cap, wires, and plugs, but I was wondering could this be a carb problem or the coil? It seems to run...
  9. T

    Lower link Pivot shaft seal MF35

    I have a 202 industrial that is doing the same thing and I was wondering if you got an answer on removing the Axle housing. Can it be reached by lifting the top plate under the seat? How extensive is it to remove the housing? Any special tools needed? Mike
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top