(800) 853-2651
SHOP NOW

Recent content by tractorboy

Yesterday's Tractor Forums
  1. T

    D14

    Any one have a D14 power steering pump?
  2. T

    I've had it!!!!!!!

  3. T

    Problem with JD 620

    Thanks guys. It was a bad resistor.
  4. T

    Problem with JD 620

    I have a JD 620 that ran fine but now only fires on an attempted ignition but will not continue to run. I changed the wiring harness, changed the points and plugs, and cleaned the Carb before the problem appeared. I even timed it before this problem arose. The tractor started fine several times...
  5. T

    problems with jd620

    I have a JD 620 that ran fine but now only fires on an attempted ignition but will not continue to run. I changed the wiring harness, changed the points and plugs, and cleaned the Carb before the problem appeared. I even timed it before this problem arose. The tractor started fine several times...
  6. T

    Tool Help needed

    Just a thought but I usually split the tractor since this is fairly easy on an old JD. Then the bolts aren"t hard to get to. I made a pipe stand to hold the front part with outriggers. I used it on a case vac, JD B, JD H, and a JD A. I support the back with wood and use a motorcycle hydraulic...
  7. T

    Loosening JD 620 wheels

    Thanks everyone, I hit the end of the axle and tightened the jam bolts as suggested in stages. I also loosed the three wedge bolts in the back. The wedges are now free. However my next problem is the jack screw, which is also frozen tight. I assume that if I remove the plug on the other end I...
  8. T

    Loosening JD 620 wheels

    Thanks, I will try both in the order presented. However, I too worry about breaking the back of the wedge off. I am also going to try putting a hydraulic ram on the back side before I try hitting the end of the axle.
  9. T

    1947 John Deere Model B Governor question

    I have rebuilt two of these governors. It could be a weight or it could be a failed bearing inside of the governor that allows the weights to move. If the bearing fails then the weights can't move. Anyway, the only solution for either is to remove the governor/fan assembly and disassemble it. DO...
  10. T

    Loosening JD 620 wheels

    I am trying to change the position of the rear wheels on my "new" 620. I have the three wedge bolts loose. I finally broke the two jam nuts free and cleaned up the rust, which prevented them from moving. However I can only turn the jam nuts to about 1/8" from their marks. I have tried working...
  11. T

    Tire shipping

    I had one shipped from MI to PA and the sender simply had UPS attach it shipping label to the tire and attached rim and sent it that way. I was the rear tire for a farmall cub. Not sure how big the tire can be to ship this way but it is worth a call to UPS or a visit to their shipping store.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top