(800) 853-2651
SHOP NOW

Recent content by TractorTech

Yesterday's Tractor Forums
  1. T

    Ford 775a back head

    Perhaps you blew the head gasket at the oil passage allowing the oil to go back into the sump. A lot of carbon on the upper cylinders
  2. T

    Need help with new tires/ wheels on my Ford 4500.

    That's pretty much what it means. I assume you have a 3pt hitch and box scraper on the back and not a backhoe. Even so, the tire/wheel combination without water or weights adds quite a bit of counterbalance to the loader, but actually, you need to water the tires and realistically add weights to...
  3. T

    New to me 430 forklift

    Indeed it is a Case 430 forklift, but Harlo Corp made most of the early forlift mast and frames for manufacturers to sell under their name. ie: Case, Deere, Massey Ferguson As far as brakes are concerned, any of the 60s and 70s utility backhoes, skiploaders or forklifts has lousy brakes...
  4. T

    Need help with new tires/ wheels on my Ford 4500.

    Grab them if you want, BUT, 12.4 vs 16.9 is quite a bit less traction and weight capacity
  5. T

    Ford 4600 Bubbling in Coolant Reservoir

    I agree with previous comments, but would suggest when you flush again, pull the petcock fitting on the right side of the block just behind the injection pump. Most likely you have quute a bit of sedimentation in the lower water jacket.
  6. T

    MF135 new water pump leaks issue

    I did a Massey pump not long ago. Pretty sure the bolt holes are blind holes. The plate is there to take the wear of the impeller instead of it wearing the face of the block. The gasket is pretty straight forward, no particular position to install. Are your sutfaces clean and smooth?
  7. T

    7600 turbo oil supply/drain line gaskets

    I don't see why not
  8. T

    7600 turbo oil supply/drain line gaskets

    This picture is off of a 7610 tractor. The sleeves are to the right.
  9. T

    Ford 775a back head

    Could be either clog or low pressure. You should be able to tap into oil passage for a gauge from either plug on the front or back side of the filter
  10. T

    New to me 430 forklift

    Nice unit. Looks like a Harlo mast.
  11. T

    Does my ford 7000 have the correct connecting rod bearings installed?

    Agreed. The parts pages specify "not for 7000" on all that are not for 7000. Attached is a picture of bearings for 7000s with the holes in them for lube. Likewise though, the rod bushing for 7000s have a hole, so without fully disassembling the engine, you're not going to know. I don't remember...
  12. T

    Is this a 30B?

    Yup, that's a 30B. Drain the fuel and refill with diesel. Those fuel systems are pretty forgiving. The cover over the fuel was probably an anti-theft cover so that it could be padlocked.
  13. T

    Is this a 30B?

    Then you have something else. Verify engine model and give us some pictures!
  14. T

    Is this a 30B?

    To add to @Jim.ME, the front of the hoods are the lower right of the illustration. That might be part of the confusion. And, I don't know why I asked about engine make/model, the Perkins gas is only 3 cylinder.
  15. T

    Is this a 30B?

    What make/model of engine? Should be a Continental if it is a 30B.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top