(800) 853-2651
SHOP NOW

Recent content by travis miranowski

Yesterday's Tractor Forums
  1. T

    1206 mcv valve noise

    Thanks for the ideas, the tractor is 2 hours away from where I live. So I am just trying to get prepared by ordering the parts I might need ahead of time so when I get there I can figure it out and complete it in one trip. I will first re-check the oil level and check the operating pressure...
  2. T

    1206 mcv valve noise

    Tractor vet, I really don't appreciate your condescending answer. Did I ask you to wave your magic wand? All I am asking for is some advice from someone a little more familiar with this tractor than I am! As far as being a novice, hardly. I have been wrenching my whole life. 15 years as a...
  3. T

    1206 mcv valve noise

    Thanks, no it is not the gear mesh, I checked that before I installed the bottom cover. And it does not sound like a gear noise. It is a hydraulic whine.
  4. T

    1206 mcv valve noise

    I recently finished rebuilding a 1206. I overhauled the engine, installed new TA, and completely went through the MCV valve. Everything works as intended but when the engine is over mid throttle the MCV valve starts making a whining noise like oil is bypassing. If I cycle the clutch to move...
  5. T

    F12 carburetor

    I have dealt with Denny's once and that was enough. He is a complete jerk and does poor work! Hard to believe he gets any business! First, I would check for any vacuum leaks by spraying some carb cleaner around the intake manifold while running. Make sure compression feels even between the...
  6. T

    1206 restoration

    As far as the paint, I am not sure what brand they used. It was done by a local body shop in pieces and I re-assembled. I know the tin work is base clear but the rest I think is single stage.
  7. T

    1206 restoration

    Thanks, I could not agree more on the stack. We ordered most parts from Steiner and I was disappointed when I opened the box. Should have sent it back. I don't know why anyone would want that big stack on top of a 4" pipe. It does look very goofy! I think I will talk the owner into finding...
  8. T

    1206 restoration

    It has one issue that maybe the Farmall brain trust can help me out with. When the engine is revved up over half throttle and brought back to idle once in a while the MCV valve starts making a high pitched whining noise that goes away if you bump the dump valve lever a little bit. I have it...
  9. T

    1206 restoration

    Here are a few pictures I thought I would share of a tractor I have been working on off and on for 3 years. It belongs to someone else but I did all the mechanical work. The paint was done by a local body shop. The sheet metal has a Base/clear finish and it is like a mirror! The tractor sat...
  10. T

    JD 9520T

    The rear ends are a little weak in them. There is a replacement cover for the rear end that solves the biggest problem. Might want to check to see if it has been updated. If you don?t catch it in time and it fails it is $10,000 plus. I had one strip the splines out of the diff carrier too...
  11. T

    Identify cart

    Fairbanks Morse 6hp ZA cart.
  12. T

    10 gals of 30 weight non detergent

    Ultradog, where are you located? I am in New Prague. I collect hit and miss engines and use that oil. I would be interested in that oil.
  13. T

    John Deere cast iron painting

    If you are using enamel paint add hardener.
  14. T

    What's power pack for on G1000?

    I don?t think the whole system was banned but rather the ?tar? inside the transformer contained PCB,s like early flourescent light ballasts. I suspect they quit using the system because it was overly complicated and expensive to maintain compared to standard lights.
  15. T

    Engine machine shop work

    X2 what has already been said!!!! I would never grind just one journal. Grinding just one is not a good practice and you did not really pay any extra. The work in turning a crank is in the setup not the actual grinding. And by grinding just one, you are going to be forced to buy individual...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top