(800) 853-2651
SHOP NOW

Recent content by trouttman

Yesterday's Tractor Forums
  1. T

    8n overdrive cable shifter

    I made one from an emergency brake cable, cut the ends off of the rusted one and braze them on the brake cable.
  2. T

    Snow plowing

    I turn the blade backwards, it will get it down to about 1/2 - 1", drive on it a few times and most of it is gone or melt if sun hits it. Trouttman
  3. T

    No fuel or no fire?

  4. T

    2N Carb

    Don't know what your problem is with the carb, rebuilt mine 30+ years ago when the engine was rebuilt, I have to adjust it occasionally. A Few years ago I thought I had a carb problem, turned out to be electrical. Before spending $35-45 on something that may work, I would contact one of the...
  5. T

    Ford 8N choke rod/knob

    I use a wire nut for the knob, rod is original.
  6. T

    51 8N pinion gear

    I had to replace ring gear, pinion and spider gears in my 2n about 20 years ago, Nothing matched had to get from several sources, bearings and spider gears were new, ring and pinion used from 2 different sources, no problems. so far. trouttman.
  7. T

    REPOST - battery/electrical decisions

    Before I converted mine, I went thru 3 batteries in 6 years using a battery maintainer, prior to that I didn't have a problem with 6v batteries that would last for 5-6 years no problems. I also have a truck and jeep and they all use the same size battery. I put the newest battery in the jeep...
  8. T

    REPOST - battery/electrical decisions

    It's your tractor, but the best $200.00 that I have spent in the last few years on something other than women and wine was a 12v converson from this site and new battery from wally world. The reason, could not find a 6v that would last more than a year on a tender.
  9. T

    Front steel wheels

    there is a parts supplier that has free shipping, I bought 2 front wheels a couple years ago, free shipping over $99.00. Can't post there name, this website forbids it. someone may know how. just 8.... n...s . com take out the ....
  10. T

    How to Rivet Rear 9N Fender Shells to the Braces ??

    Larry, what Greg sent is the rivet tools that fit into an air rivet gun, you also need a bucking bar, Google aircraft rivet gun and bucking bar. The rivet tool and gun hammers the flat side of the rivet against the bucking bar. If you use the right tool it will not damage the fender. that is how...
  11. T

    No acceleration

    Setting 4 years ethanol gas? enough said
  12. T

    No acceleration

    Setting 4 years ethanol gas? enough said
  13. T

    8N starting problem.

    How can it rufuesto turnover but crank extremely hard/slow?
  14. T

    1952 8N 12 volt wiring went gunnysack

    Looks like you have the ignition switch wired to the wrong terminal on the oem resistor, plus you have the lights hooked to the wrong terminal. Like H. Cooke said google JMOR's wiring diagrams. Trouttman
  15. T

    EBay warning, popgun48

See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top