(800) 853-2651
SHOP NOW

Recent content by trustyt

Yesterday's Tractor Forums
  1. S

    Straightening bent metal

    The grill portion of the hood on a 2015 Jeep Cherokee has been pulled out about 12 inches from where it should be. Hoods have an inner structure that is tougher to bend than the outer skin. Would I be crazy to cut the inner structure with a cut off wheel and then bend the hood back down and then...
  2. C

    Model 62 Tires

    Good Morning Gentlemen, a while back (probably over a decade ago) we decided to put newer rubber on the rear of our Model 62 as the original rear tires were in rather poor condition. At the time, we decided to put the originals in the shed because they were "the originals." When cleaning out...
  3. K

    Super C / 100 hydraulic pump

    Are the hydraulic pumps for a 100 and Super C the same ? Thanks
  4. H

    Auction at Upland Nebraska

    Results from March 2 auction. Oliver 70 with 2 row cultivator $4200 Oliver 77 gas WF restored $5100 Oliver Super 55 gas restored $6400 Oliver 880 mist green,WF original SN 73782-873 $19000
  5. T

    dumbfounded

    Hi, that RV2B mag has to be timed correct. You may be hitting on the LH from the terminal that is designed for the RH and firing the right plug in the exhaust stroke from the LH terminal. Those RV2B's are not like a Wico that hits every other snap. They only hit once in 360, and back to back, so...
  6. T

    Ensign carb

    The carb has value, good that you were able to save it from the smelter. trustyt
  7. T

    Titan Tires

    I believe that Titan bought the ag tire business that Good Year had in the past year, so you will see a lot of Titan tires. Trustyt
  8. T

    1942 John Deere H parts needed

    Hi, I have an H air cleaner and a drawbar, as well as many other H parts. Email me and let me know your needs if you have not located what you need locally. Good luck, Ted.
  9. T

    rear weights on a 720 Standard

    Leo, Your 720 Standard would take an F1592R rear weight. I think the R# weights were for new gen standards, and have a smaller bolt pattern footprint. Your parts book should be able to confirm the F1592R Pt#. I have that Pt# castings on my 630 and 730 Standards. Ted.
  10. T

    Well this kinda sucks......

    They used to make a coiled wire that went in the lower hoses to keep them from collapsing from the pull of the water pump, and before they improved the composition of the hoses. If you could come up with one of those coil inserts, they sort of work like a pipe bender and keep the hose from...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top