(800) 853-2651
SHOP NOW

Recent content by TSK

Yesterday's Tractor Forums
  1. T

    FEL plumbing on a 4020 with no rock shaft

    Tx Jim-Thanks, much appreciated.
  2. T

    FEL plumbing on a 4020 with no rock shaft

    Tx Jim, Do you know what size ORB fitting fits the orifice in the transmission case?
  3. T

    FEL plumbing on a 4020 with no rock shaft

    Ok, I finally got the FEL home and am getting around to getting the brackets mounted and will plumb the control valve according to the info you guys all gave me. I have located the hex plug (where the RS return would go if equipped with a RS) where I will connect the return from the control...
  4. T

    FEL plumbing on a 4020 with no rock shaft

    I located the threaded hole in the location in the green square in the picture. Must be where the rock shaft line would connect if there was a pressure line from the priority valve. I haven’t crawled under the left side yet to find the return connection plug. Thanks again everyone.
  5. T

    FEL plumbing on a 4020 with no rock shaft

    I can’t see a plug but the cab floorboard might be in the way to see it, and the tractor is back in the darker end of my shed. I see what you mean. Looking through the JD parts catalog it FINALLY sunk into my head that if the tractor would have been equipped with a rock shaft, the control...
  6. T

    FEL plumbing on a 4020 with no rock shaft

    Used red- The tractor never had a rock shaft/3 point so there’s no fitting there on my tractor. Ted
  7. T

    FEL plumbing on a 4020 with no rock shaft

    You guys are the best. I believe I can figure it out now: -Install a line from the bottom outlet (where the plug is) going to my loader control valve. -run a return line from loader valve to transmission near the filter (if my tractor has the hex plug) or into the filter cover -make sure the...
  8. T

    FEL plumbing on a 4020 with no rock shaft

    Thanks Glen. I forgot to say that my tractor is a 1965 4020. Don’t know if that makes a difference. It has dual remotes. I have to locate the priority valve, where did Deere hide that? Looking at the diagrams on the JD Parts catalog online I don’t see the plug you mentioned. There are two...
  9. T

    FEL plumbing on a 4020 with no rock shaft

    Good evening, I would like to put a FEL on my 4020. My 4020 is a standard with no rock shaft. I have read here where an oil line to the loader control valve was connected to the fitting going to the rock shaft (near the brake cylinders) and then a return back to the fitting on the rock shaft...
  10. T

    FEL mounts

    Thank you. I was hoping they’d fit.
  11. T

    FEL mounts

    I’m looking at a Koyker 500 FEL that came off a 4440. Will the mounting brackets from the 4440 fit my 4020 without modifications? How does the Koyker 500 compare to a JD 148? The Koyker mounting system looks sturdier to me but the 148 gets good reviews on this site. Any info here is...
  12. T

    1209 reel bearings - where to get?

    Green parts store https://www.greenpartstore.com/search.asp?keyword=AE74534
  13. T

    1938 unstyled B

    Check the lever inside the governor housing. The two fingers on the lever should straddle the sleeve. If one of the fingers is bent it will bind/wear on the sleeve.
  14. T

    Hot Welding an Unstyled G head

    Where are you located?
  15. T

    620/630 vs 3020 gas

    “The 2010 was advertised as the replacement for the 630.” But keep the 630 to do the work while the 2010 is broke down…
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top