(800) 853-2651
SHOP NOW

Recent content by tuckerMAX

Yesterday's Tractor Forums
  1. J

    720 steering pedestal

    resealing the power steering pedestal, new bushings, bearing, o rings, cork seal, ect. question is how stiff should these be to turn with all new parts? i thank mine is tight around the bottom. when i slid the bottom quill that has thrust bearing on the shaft it got hard to turn, couldn't hold...
  2. N

    Check these out and sign if you agree

    Everyone who enjoys the practice of their 2A rights, and would like to get them back, at least to the point they were when many of your guys were young, or some of us 'younger members' were born, need to check out the links provided here, and sign the petitions of you agree. Once you do...
  3. T

    farmall h build

    ss409 is right, Youd be better off to put some effort in the rods.
  4. T

    farmall h build

    Yes. At 5.125 you have to take the webbing out. Grind the neck out of the oil galley just shy of breaking thru, and cut the cam down to 1/2" thick. With an untouched stock.rod. not to mention small.areas on the pan rail.
  5. T

    NATPA DIV 2 QUESTION

    It does not matter if mm had them or not. Bob shoots from.the hip and misses a lot.
  6. T

    2.625 rod jornal size

    Mm z jet star etc, but double check
  7. T

    Goin' to Corunna, MI?

    Heard Mopower the expert was deemend not legal after being inspected twice, cleared to pull, then getting yelled at by Bob Bryant "The Moline Expert" and a few others for having an engine that "sounded too good" and blocks that they couldnt prove were legal or not. Sounds like NATPA is up to...
  8. T

    Biggest thing that limits pull participation?

    FACTORY FARMER, are you just ignorant? You must not pull much, because jds get EVERY advantage available. Increased deck height, duplex carbs, etc. The national sanctioning bodies allow a sheet metal on g's etc...mm really gets screwed, but I doubt you know enough to realize it.
  9. T

    This can't be legal

    The hd800 didn't exist back then
  10. T

    Mid-Michigan's Best Summer Pulling

    So obviously you dont like the state of michigan..so, why would you even care enough to respond..Of course Michigan DOES have the most dominant pullers, but still, personally, I think you are just a big mouth on a saturday night with nothing to do to pass the time. Go jack off or something..But...
  11. T

    Mid-Michigan's Best Summer Pulling

    Hey ..you are a perfect example of an NATPA puller, with knowledge like that. Prove it. Either way, CAFPC scheduled their date first. It was just lousy to have a contradicted schedule, when it could have been avoided. But I dont think you are intelligent enough to understand that.
  12. T

    Mid-Michigan's Best Summer Pulling

    Dave, I happen to know for fact that cafpc continually contacted natpa as to abound a scheduling conflict. After NO answers, cafpc went with the same date as had always been....and then natpa sniped the date. I seem to rememberbthem doing this to sigorney Iowa before....its just a shame they had...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top