(800) 853-2651
SHOP NOW

Recent content by TURNER

Yesterday's Tractor Forums
  1. T

    Archie Morse in CA

    I finally got the tractor in.It was what he described. WOW that wont happen again!
  2. T

    420 S drawbar

    i have what you need. 910 876 7566 thanks
  3. T

    Archie Morse in CA

    Ive purchased a tractor from Morse in Ca,i have a bad feeling,Am I gona have to go find him? Anyone ever bought from him and recieved the product?Just wondering
  4. T

    Are JD40S Rear Axles Tapered?

    yes the are tapered, however unless you are extremely lucky you will need the puller as you described, heat,and a sledge hammer. 1. install puller and tighten 2. heat hub 3. hit end of the axle or back side of hub, it will give!
  5. T

    L HEAD TORQUE

    Thanks
  6. T

    JD40C governor problem

    sounds to me like you have something in your gas tank besides gas. I would check my fuel flow.More than likely its not a gov problem. You will know when a weight breaks or if it freezes up.
  7. T

    Large upcoming Deere auction in PA

    I dont think anyone can predict how the auction will go, but i feel it will be like most you see some high $ stuff and then you see some where you kick yourself in da tail all the way home for not buying more!What i do know is there is some very very nice tractors in his collection!!!I'll be...
  8. T

    G head gasket?

    I have a perfect head for a g that i would be willing to trade for the unstyled head.
  9. T

    Late styled AO battery cover

    mother deere had them last time i checked.
  10. T

    420 electrical

    the points inside the voltage regulator. the voltage reg is the brains of the charging system.
  11. T

    JD 40 - 12 Volt system

    since your going 12v, do you want to sell the generator?
  12. T

    420 electrical

    All above is correct, however, I had the same problem about a month ago. after 3 new volt regulators i found out the points internally were not making good contact. after that no problems she works great!
  13. T

    JD LI

    well the tractor was found in nc, however I have seen several tractors with steel mill markings,none were stamped. Wondering if it could be a Tenn DOT thing?
  14. T

    JD LI

    HAVE A JD LI WITH TENN 114 STAMPED UNDERNEATH TRACTOR ON THE ROUND TUBE. ANYONE ELSE RAN INTO THIS? I ASSUME THIS MEANS IT BELONGED TO TENN HWY DEPT.
  15. T

    JD430T front pedistal

    put a pedistal from a 40,420,430 t back in its place
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top