-
Cheap hyd oil?
Today we tore down a 3020 syncro for a top shaft trans job. Every bit of the lining had peeled off the syncro plates. I have never seen that before. One or two small pieces that were still on just flaked off with my fingernail. Was it defective parts (tractor had been apart before), water in the...- tomstractorsandtoys
- Post #1
- Forum: John Deere
-
T
stair lift.
What is a good brand? I have an acron & am, discusted with it. Very costly to keep going& I can't do stairs without it. Got it new in 2014 & it sounds like the motherboard went out again. 2nd one along with some failed relays. Repairman can't come until Fri. so I am stuck in the house until...- teddy52food
- Post #1
- Forum: Tool Talk
-
B
John Deere #11 combine
How rare is a John Deere #11 combine with the cutter bar on the right side of the hitch?- Bob861
- Post #1
- Forum: Combines and Harvesters
-
Mower tires
A guy I know is looking for 2 tires for his Oliver sickle mower, sorry, I don't know the model number. He said it has 2 solid tires on the back. Any idea where to find tires for it??- super99
- Post #1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
F
Drill press chuck where to find
A jaw broke in this chuck. I never did like it so I am on the hunt for a new keyless chuck that is high quality. I dont care what it costs within reason. It is Jacobs taper, the hole is 3/4 inch. I dont know my sizes but a number 3 is stamped on the side. It will chuck a 5/8 bit. The other day...- fixerupper
- Post #1
- Forum: Tool Talk
-
D
Borderline Overheating
Just a old school trick for a older tractor with a Copper/Brass Radiator. Not sure if it will help with anything such as aluminum. If your tractor has been running warm, and is now borderline hot, heres a couple of tricks I learned years ago in the radiator shop. 1. Clean the outside... -
J
Trailer seam rust
I have a 3 horse slant load trailer Id like to rebuild for animal rescue training (We have mannequins we put in the trailer and flip it (It has roll bars) and practice extricating the animals.). It is for a professional first responder training service a friend runs so all repairs need to look...- JimS
- Post #1
- Forum: Tractor & Farm Talk
-
S
Load control shaft replacement
Is there a certain setting to put the draft control lever in when replacing the shaft ?- SVcummins
- Post #1
- Forum: John Deere
-
8N dipstick measrement needed ....
The tranny dipstick on the right side of an 8N transmission has the little tin 'cup' not attached to the dip stick blade. Can someone give me a measurement from the bottom of the blade to the top of where that little dust cap should be attached to the blade? The way it is, I can't get an...- Crazy Horse
- Post #1
- Forum: Ford 9N, 2N & 8N
-
-
F
60 ignition resistor?
Should a 60 have a 6v coil with a resistor in line or a 12 volt coil with no resistor? I have a hunch it should have a 12 volt coil but I thought I would ask you guys first. I have a customer 60 in the shop with a new 6V coil and burned points. I cannot find evidence of a resistor behind the...- fixerupper
- Post #1
- Forum: John Deere
-
J
Versatile 145 painted
I wanted to share the pic of my 145 painted up. Its not show room quality but it sure looks better than it did! -
D
allis hd4 dozer stops moving under load
I HAVE A ALLIS HD4 THAT I REBUILT THE ENGINE AND STEARING CLUTCHES , ITS BEEN SITTING FOR YEARS , IT GOES INTO FORWARD AND BACK FINE AND DRIVES ALL OVER BUT WHEN I GET TO A HILL IT STOPS MOVING , 1ST GEAR IT WILL PULL ITS SELF BUT 2ND OR 3RD IT WILL STOP MOVING ? ANY SUGGESTIONS ? iM THINKING...- DoRobben
- Post #1
- Forum: Allis-Chalmers
-
gray and grey pic. posting.
i dont know what with that topic but cant even see the reply button to post if i wanted to. everything is so big. all the other post are normal except that one.- rustred
- Post #1
- Forum: Tractor & Farm Talk
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy