(800) 853-2651
SHOP NOW

Recent content by vern-45

Yesterday's Tractor Forums
  1. V

    pulling season coming to end

    i need to unstuck gleaner engine,regrind cam,head work,wd pistons,gov. spring,wheelie bars,other than that?
  2. V

    e gleaner

    are there any engine re-ring kits out there you recomend?are there any to stay away from?
  3. V

    e gleaner

    how much cranking pressure would that be?my stock wd-45 runs about 100psi.thanks.
  4. V

    e gleaner

    i wonder if i should run wd 70cc dished pistons in my gleanerE pulling motor?the top of piston to center of wrist pin measurement is 2&11-16 inches.MLPankey said he could figure my compression ratio with these measurememts.any help would be very welcome!mike-
  5. V

    wc governor

    agco has a gov. spring for a wc,it comes from a 175.i think it runs about 1800 rpms.for about 40 bucks you are the new owner.
  6. V

    Wc/Wd Ring Pinion

    i believe the only cam that will help him would be a 175 cam. the others areall the same.
  7. V

    STOCK PULLING

    hey doug,missed you at volga on saturday.not much of a turnout there.nobody in my first two classes.i got a 4th place in 4500 though.starting to work on e-gleaner motor a little bit.see ya.Mike-
  8. V

    Gathering of the Orange at Prairie Village 2009

    we need to thank Doug and the Shellums for putting on the tractor pull also.the idea of running 2 sleds on that track worked out really well.there were a lot of hooks there,including mine,that day it moved right along.thank-you all! mike a.
  9. V

    WD45

    take your shifter out and completely rebuild it,like i did,ibelieve to use 80w-90 oil in the gears.your hand clutch has shims in it , they are located in the the clutch under the battery box,if the shims are all gone,you have to hold or chain the hand clutch back.good luck.
  10. V

    WD 45 loss of coolant

    coolant may be leaking out of your weep hole on the bottom of your water pump neck.
  11. V

    pulling e-gleaner

    i don't have the pistons out of the block,but the head is off. the pistons are flattops.more info to follow later.thanks.
  12. V

    pulling e-gleaner

    i just got my e-gleaner engine home last weekend.i will be rebuilding this currently stuck engine into a hopefully decent pulling engine.175 cam is in the works.i believe,this motor is the M version,i think the comp.ratio is only about 7.2to1.i have a set of wc flat top pistons and rods,will...
  13. V

    Cylinder pressures on pulling tractors

    how do you get over 300lbs. cranking pressure from a 226 allis?
  14. V

    WD engine

    have your cam ground to 175 specs.install a gov.spring for a 175 also.have fun!
  15. V

    GLEANER E NEEDS A LITTLE

    does a stock gleaner e engine only have 50hp?i thought they had at least 60.also,go with the 9 spring pressure plate,i believe the wd45 used them.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top