(800) 853-2651
SHOP NOW

Recent content by Vic S

Yesterday's Tractor Forums
  1. F

    Raakos - tie rod tubes

    Sorry I didn't get back to you sooner - I got a little busy with haying. The pair of tie rod tubes I have are the 15.75" size that you need. The inner ends are still usable, but the outer ends are worn out. I'll remove them to save some weight for shipping. Let me know if you still need...
  2. V

    petronics

    Gary is exactaly right, I burned up two, that we got from Denny's, ordered electronic ign and high output coils from then, The woman that answeres the phone didn't understand and didn't care. Called the guy from Colorado (CBS) he told me what was wrong, and even offered to warrenty, dennys ign...
  3. V

    Hey Farmall H guys

    A electric is much better you can cool it off with the motor shut off, plus warm up faster. I went to the junk yard and looked til I found one that would fit in my space. Then I mounted it in front of the radiator, so it blowes to the front. plus a 12 volt pump from Northern, 5 gal a minute. It...
  4. V

    OT 4 Wheeler

    We have a 4X4 yamaha 250 and a polaris 4x4 425 But what I use is a lifted easy=go golf cart with traction tires and a seat/bed on the back has the orignal bin under the bed plus bins in the dash and cup holders. the engine starts when you push the foot feed and dies when you let up. The dealers...
  5. V

    top link

    Look on your plow etc. It is easy to cut one of the adjusters and weld it back together.I just use a one inch ready thread. but its not as neet.
  6. V

    rearend oil

    I run 75 X 90 syn and keep it low
  7. V

    Will a 310 Diesel fit in a 77 frame ?

    Its supposed to. Its water pump is a little long, and a direct inj manafolds are a little wide.Motor mounts are a direct fit. need your orignal flywheel and bell housing.
  8. V

    Where is everybody finding 310 motors?

    We have a 310 Diesel indirect Inj, Complete for 1000 Located se Il, 6188382225
  9. V

    putting together an allis motor

    Like I"ve said before, get it stroked to 5 in and use your 45 parts you will be competive, and can pull 15.5 X 38"s have fun.
  10. V

    dished or flat top?

    I had 460 ford smog pistons in our wc(they have a cut out in the top) It ran real well would pull second with 15.5's at 3500lb. Changed to 10.5 flat top ford pistons, will power out in second now. hasn't any lug. but has more power reved up. I think would be better with dished pistons and longer...
  11. V

    Is a JD435 a 30 series JD

    I just loaded up and took my toys home, and yes I have been lucky a time or two.
  12. V

    electric fans

    Also you can cool it off with-out runing the engine.
  13. V

    Is a JD435 a 30 series JD

    I drove over to Princeton In. to the napa pull thinking I would have a day of fun pulling. But when I went to ask for my 2010 sticker, The guy said we have a problem with you pulling with us your tractor is a 58 model and our cut off is 57. I said yes but your rules say except 30 series JD I...
  14. V

    princeton NATPA schedule

    I read somewhere there was just one sled, but they will surely have two. I"m loaded up amd will leave early in the morning. see you-all there. The next question will it start when we get there.
  15. V

    Anybody have any JD-4010 wedge style 9 bolt hubs??

    Aren;t they the same as a 4020 or a 4430 with diffrent weges.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top