(800) 853-2651
SHOP NOW

Recent content by vp

Yesterday's Tractor Forums
  1. V

    99 F350 brake lights

    Sounds like a ground or a fuse some vehicles are wired that if your dash lights are out then you have no tail lights blown fuse
  2. V

    Ferguson sleeves

    Have done many of these sleeves pull the sleeves out check to see if you cut one putting it in, also check to see if the webs in the block are cracked or pittedwhen installing the sleeves I do not use oil or grease . use liquid dish soap on the o rings or murphy oil soap [ make sureyou get it...
  3. V

    New tractor barn

    Does that bring back memories pouring walls, ran concrete pumps since 1971 retired 10 years ago,said I had enoughthen the company would call me to fill in ever once in awhile , Last job 2 years ago 600 plus yards on abridge deck, that when I said Iam 67 years old and don't need the stress any...
  4. V

    3pt lift arms

    Looks like the ones on a 135 or 150. Why don't you just change the crank handle from your old leveling box to this one. On the back side is a rivet just grind the head off and drive it out remove cranks and install new rivet
  5. V

    53 jubalee

    make sure the hubs are not worn on the splines .if they are they make undersize hubs [on the splines] clean up the splines and hub real good [brake cleaner] put silicone inside of the hubs and tighten the axle nut TIGHT I mean real TIGHT if you don't the hub will loosen up and you will get oil...
    • vp
    • Post #1
    • Forum: Ford
  6. V

    MF 50 hydraulic pump removal

    if it has multi power then it has to be split between the transmission and differental block the front and roll the back away pump will come out then with the multi power pump any questions call 740 982 7446
  7. V

    Massey Ferguson 235 Issues?

    the ones with power steering had problems manual steering were ok just keep everthing greased on the steeting
  8. V

    to35 steering

    also make sure the toe in is correct 1/8 to 1/4 toe in
  9. V

    to35 steering

    another thing that is happening is the steering gears are bottoming out before it hits the stops on the spindles the way to fix this is to weld 1/4 key way on the stops on the spindles that will stop the gears from bottoming out you will never notice the differance in the turning radius if you...
  10. V

    Its a law! LOL

    back before I retired I worked for a large construction co as a mechanic one day i was covered with oil and grease one of the guys asked me how do you ever get clean ? my answer pamolive dish soap I shower in it still do today been retired 10 years
  11. V

    Is the MF 235 an Orphan year?

    These tractors had alot of steering problems that is why they ony were made in 1975 and 1976
  12. V

    Massey Ferguson 3 Bottom Plow

    Give me acall and I will answer your questions about the plows Thanks Vic 740 982 7446
  13. V

    175 Transmission noise

    Don,t see any shop rags in the filter screen !!!!!!!
  14. V

    Massey ferguson 202 no pto but would like to add help

    give me acall and iwill tell you what to look for and do to seeif it will work 740 982 7446
  15. V

    miner09

    replaced the manifold on my to 30 bought it from stieners made in U S A did not have to do anything bolted right up
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top